CVE-2025-39948

Published Oct 4, 2025

Last updated 3 months ago

CVSS medium 5.5

Overview

Description
In the Linux kernel, the following vulnerability has been resolved: ice: fix Rx page leak on multi-buffer frames The ice_put_rx_mbuf() function handles calling ice_put_rx_buf() for each buffer in the current frame. This function was introduced as part of handling multi-buffer XDP support in the ice driver. It works by iterating over the buffers from first_desc up to 1 plus the total number of fragments in the frame, cached from before the XDP program was executed. If the hardware posts a descriptor with a size of 0, the logic used in ice_put_rx_mbuf() breaks. Such descriptors get skipped and don't get added as fragments in ice_add_xdp_frag. Since the buffer isn't counted as a fragment, we do not iterate over it in ice_put_rx_mbuf(), and thus we don't call ice_put_rx_buf(). Because we don't call ice_put_rx_buf(), we don't attempt to re-use the page or free it. This leaves a stale page in the ring, as we don't increment next_to_alloc. The ice_reuse_rx_page() assumes that the next_to_alloc has been incremented properly, and that it always points to a buffer with a NULL page. Since this function doesn't check, it will happily recycle a page over the top of the next_to_alloc buffer, losing track of the old page. Note that this leak only occurs for multi-buffer frames. The ice_put_rx_mbuf() function always handles at least one buffer, so a single-buffer frame will always get handled correctly. It is not clear precisely why the hardware hands us descriptors with a size of 0 sometimes, but it happens somewhat regularly with "jumbo frames" used by 9K MTU. To fix ice_put_rx_mbuf(), we need to make sure to call ice_put_rx_buf() on all buffers between first_desc and next_to_clean. Borrow the logic of a similar function in i40e used for this same purpose. Use the same logic also in ice_get_pgcnts(). Instead of iterating over just the number of fragments, use a loop which iterates until the current index reaches to the next_to_clean element just past the current frame. Unlike i40e, the ice_put_rx_mbuf() function does call ice_put_rx_buf() on the last buffer of the frame indicating the end of packet. For non-linear (multi-buffer) frames, we need to take care when adjusting the pagecnt_bias. An XDP program might release fragments from the tail of the frame, in which case that fragment page is already released. Only update the pagecnt_bias for the first descriptor and fragments still remaining post-XDP program. Take care to only access the shared info for fragmented buffers, as this avoids a significant cache miss. The xdp_xmit value only needs to be updated if an XDP program is run, and only once per packet. Drop the xdp_xmit pointer argument from ice_put_rx_mbuf(). Instead, set xdp_xmit in the ice_clean_rx_irq() function directly. This avoids needing to pass the argument and avoids an extra bit-wise OR for each buffer in the frame. Move the increment of the ntc local variable to ensure its updated *before* all calls to ice_get_pgcnts() or ice_put_rx_mbuf(), as the loop logic requires the index of the element just after the current frame. Now that we use an index pointer in the ring to identify the packet, we no longer need to track or cache the number of fragments in the rx_ring.
Source
416baaa9-dc9f-4396-8d5f-8c081fb06d67
NVD status
Analyzed
Products
linux_kernel

Risk scores

CVSS 3.1

Type
Primary
Base score
5.5
Impact score
3.6
Exploitability score
1.8
Vector string
CVSS:3.1/AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H
Severity
MEDIUM

Weaknesses

nvd@nist.gov
CWE-401

Social media

Hype score
Not currently trending

Configurations

Related CVEs

  1. In the Linux kernel, the following vulnerability has been resolved: ibmveth: Disable GSO for packets with small MSS Some physical adapters on Power systems do not support segmentation offload when the MSS is less than 224 bytes. Attempting to send such packets causes the adapter to freeze, stopping all traffic until manually reset. Implement ndo_features_check to disable GSO for packets with small MSS values. The network stack will perform software segmentation instead. The 224-byte minimum matches ibmvnic commit <f10b09ef687f> ("ibmvnic: Enforce stronger sanity checks on GSO packets") which uses the same physical adapters in SEA configurations. The issue occurs specifically when the hardware attempts to perform segmentation (gso_segs > 1) with a small MSS. Single-segment GSO packets (gso_segs == 1) do not trigger the problematic LSO code path and are transmitted normally without segmentation. Add an ndo_features_check callback to disable GSO when MSS < 224 bytes. Also call vlan_features_check() to ensure proper handling of VLAN packets, particularly QinQ (802.1ad) configurations where the hardware parser may not support certain offload features. Validated using iptables to force small MSS values. Without the fix, the adapter freezes. With the fix, packets are segmented in software and transmission succeeds. Comprehensive regression testing completedd (MSS tests, performance, stability).•CVE-2026-46273
  2. In the Linux kernel, the following vulnerability has been resolved: coresight: tmc-etr: Fix race condition between sysfs and perf mode When trying to run perf and sysfs mode simultaneously, the WARN_ON() in tmc_etr_enable_hw() is triggered sometimes: WARNING: CPU: 42 PID: 3911571 at drivers/hwtracing/coresight/coresight-tmc-etr.c:1060 tmc_etr_enable_hw+0xc0/0xd8 [coresight_tmc] [..snip..] Call trace: tmc_etr_enable_hw+0xc0/0xd8 [coresight_tmc] (P) tmc_enable_etr_sink+0x11c/0x250 [coresight_tmc] (L) tmc_enable_etr_sink+0x11c/0x250 [coresight_tmc] coresight_enable_path+0x1c8/0x218 [coresight] coresight_enable_sysfs+0xa4/0x228 [coresight] enable_source_store+0x58/0xa8 [coresight] dev_attr_store+0x20/0x40 sysfs_kf_write+0x4c/0x68 kernfs_fop_write_iter+0x120/0x1b8 vfs_write+0x2c8/0x388 ksys_write+0x74/0x108 __arm64_sys_write+0x24/0x38 el0_svc_common.constprop.0+0x64/0x148 do_el0_svc+0x24/0x38 el0_svc+0x3c/0x130 el0t_64_sync_handler+0xc8/0xd0 el0t_64_sync+0x1ac/0x1b0 ---[ end trace 0000000000000000 ]--- Since the enablement of sysfs mode is separeted into two critical regions, one for sysfs buffer allocation and another for hardware enablement, it's possible to race with the perf mode. Fix this by double check whether the perf mode's been used before enabling the hardware in sysfs mode. mode: [sysfs mode] [perf mode] tmc_etr_get_sysfs_buffer() spin_lock(&drvdata->spinlock) [sysfs buffer allocation] spin_unlock(&drvdata->spinlock) spin_lock(&drvdata->spinlock) tmc_etr_enable_hw() drvdata->etr_buf = etr_perf->etr_buf spin_unlock(&drvdata->spinlock) spin_lock(&drvdata->spinlock) tmc_etr_enable_hw() WARN_ON(drvdata->etr_buf) // WARN sicne etr_buf initialized at the perf side spin_unlock(&drvdata->spinlock) With this fix, we retain the check for CS_MODE_PERF in get_etr_sysfs_buf. This ensures we verify whether the perf mode's already running before we actually allocate the buffer. Then we can save the time of allocating/freeing the sysfs buffer if race with the perf mode.•CVE-2026-46272
  3. In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: do WoW offloads only on primary link In case of multi-link connection, WCN7850 firmware crashes due to WoW offloads enabled on both primary and secondary links. Change to do it only on primary link to fix it. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1•CVE-2026-46271
  4. In the Linux kernel, the following vulnerability has been resolved: power: supply: rt9455: Fix use-after-free in power_supply_changed() Using the `devm_` variant for requesting IRQ _before_ the `devm_` variant for allocating/registering the `power_supply` handle, means that the `power_supply` handle will be deallocated/unregistered _before_ the interrupt handler (since `devm_` naturally deallocates in reverse allocation order). This means that during removal, there is a race condition where an interrupt can fire just _after_ the `power_supply` handle has been freed, *but* just _before_ the corresponding unregistration of the IRQ handler has run. This will lead to the IRQ handler calling `power_supply_changed()` with a freed `power_supply` handle. Which usually crashes the system or otherwise silently corrupts the memory... Note that there is a similar situation which can also happen during `probe()`; the possibility of an interrupt firing _before_ registering the `power_supply` handle. This would then lead to the nasty situation of using the `power_supply` handle *uninitialized* in `power_supply_changed()`. Fix this racy use-after-free by making sure the IRQ is requested _after_ the registration of the `power_supply` handle.•CVE-2026-46270
  5. In the Linux kernel, the following vulnerability has been resolved: pinctrl: canaan: k230: Fix NULL pointer dereference when parsing devicetree When probing the k230 pinctrl driver, the kernel triggers a NULL pointer dereference. The crash trace showed: [ 0.732084] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000068 [ 0.740737] ... [ 0.776296] epc : k230_pinctrl_probe+0x1be/0x4fc In k230_pinctrl_parse_functions(), we attempt to retrieve the device pointer via info->pctl_dev->dev, but info->pctl_dev is only initialized after k230_pinctrl_parse_dt() completes. At the time of DT parsing, info->pctl_dev is still NULL, leading to the invalid dereference of info->pctl_dev->dev. Use the already available device pointer from platform_device instead of accessing through uninitialized pctl_dev.•CVE-2026-46269

References

Sources include official advisories and independent security research.