Keyless entry vulnerabilities

OpenClaw before 2026.3.28 contains a privilege escalation vulnerability in the /pair approve command path that fails to forward caller scopes into the core approval check. A caller with pairing privileges but without admin privileges can approve pending device requests asking for broader scopes including admin access by exploiting the missing scope validation in extensions/device-pair/index.ts and src/infra/device-pairing.ts.

In the Linux kernel, the following vulnerability has been resolved: nfc: rawsock: cancel tx_work before socket teardown In rawsock_release(), cancel any pending tx_work and purge the write queue before orphaning the socket. rawsock_tx_work runs on the system workqueue and calls nfc_data_exchange which dereferences the NCI device. Without synchronization, tx_work can race with socket and device teardown when a process is killed (e.g. by SIGKILL), leading to use-after-free or leaked references. Set SEND_SHUTDOWN first so that if tx_work is already running it will see the flag and skip transmitting, then use cancel_work_sync to wait for any in-progress execution to finish, and finally purge any remaining queued skbs.

Securing externally available CAN wires can easily allow physical access to the CAN bus, allowing possible injection of specially formed CAN messages to control remote start functions of the vehicle.  Testing completed on Tesla Model 3 vehicles with software version v11.1 (2023.20.9 ee6de92ddac5). This issue affects Model 3: With software versions from 2023.Xx before 2023.44.

Use of fixed learning codes, one code to lock the car and the other code to unlock it, the Key Fob Transmitter in KIA-branded Aftermarket Generic Smart Keyless Entry System, primarily distributed in Ecuador, which allows a replay attack. Manufacture is unknown at the time of release.  CVE Record will be updated once this is clarified.

Use of fixed learning codes, one code to lock the car and the other code to unlock it, in the Key Fob Transmitter in Cyclone Matrix TRF Smart Keyless Entry System, which allows a replay attack. Research was completed on the 2024 KIA Soluto.  Attack confirmed on other KIA Models in Ecuador.

An issue was discovered on certain Nuki Home Solutions devices. The HTTP API exposed by a Bridge used an unencrypted channel to provide an administrative interface. A token can be easily eavesdropped by a malicious actor to impersonate a legitimate user and gain access to the full set of API endpoints. This affects Nuki Bridge v1 before 1.22.0 and v2 before 2.13.2.

An issue was discovered on certain Nuki Home Solutions devices. Lack of certificate validation on HTTP communications allows attackers to intercept and tamper data. This affects Nuki Smart Lock 3.0 before 3.3.5, Nuki Bridge v1 before 1.22.0 and Nuki Bridge v2 before 2.13.2.

An issue was discovered on certain Nuki Home Solutions devices. By sending a malformed HTTP verb, it is possible to force a reboot of the device. This affects Nuki Bridge v1 before 1.22.0 and v2 before 2.13.2.

An issue was discovered on certain Nuki Home Solutions devices. Some BLE commands, which should have been designed to be only called from privileged accounts, could also be called from unprivileged accounts. This demonstrates that no access controls were implemented for the different BLE commands across the different accounts. This affects Nuki Smart Lock 3.0 before 3.3.5 and Nuki Smart Lock 2.0 before 2.12.4.

An issue was discovered on certain Nuki Home Solutions devices. An attacker with physical access to the circuit board could use the SWD debug features to control the execution of code on the processor and debug the firmware, as well as read or alter the content of the internal and external flash memory. This affects Nuki Smart Lock 3.0 before 3.3.5, Nuki Smart Lock 2.0 before 2.12.4, as well as Nuki Bridge v1 before 1.22.0 and v2 before 2.13.2.

An issue was discovered on certain Nuki Home Solutions devices. It is possible to send multiple BLE malformed packets to block some of the functionality and reboot the device. This affects Nuki Smart Lock 3.0 before 3.3.5 and Nuki Smart Lock 2.0 before 2.12.4.

An issue was discovered on certain Nuki Home Solutions devices. The code used to parse the JSON objects received from the WebSocket service provided by the device leads to a stack buffer overflow. An attacker would be able to exploit this to gain arbitrary code execution on a KeyTurner device. This affects Nuki Smart Lock 3.0 before 3.3.5 and 2.0 before 2.12.4, as well as Nuki Bridge v1 before 1.22.0 and v2 before 2.13.2.

An issue was discovered on certain Nuki Home Solutions devices. An attacker with physical access to this JTAG port may be able to connect to the device and bypass both hardware and software security protections. This affects Nuki Keypad before 1.9.2 and Nuki Fob before 1.8.1.

Sciener locks' firmware update mechanism do not authenticate or validate firmware updates if passed to the lock through the Bluetooth Low Energy service. A challenge request can be sent to the lock with a command to prepare for an update, rather than an unlock request, allowing an attacker to compromise the device.

Some Sciener-based locks support plaintext message processing over Bluetooth Low Energy, allowing unencrypted malicious commands to be passed to the lock. These malicious commands, less then 16 bytes in length, will be processed by the lock as if they were encrypted communications. This can be further exploited by an attacker to compromise the lock's integrity.

A vulnerability, which was classified as problematic, has been found in Munsoft Easy Outlook Express Recovery 2.0. This issue affects some unknown processing of the component Registration Key Handler. The manipulation leads to denial of service. Local access is required to approach this attack. The exploit has been disclosed to the public and may be used. The identifier VDB-252677 was assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

Missing encryption in the NFC tags of the Flient Smart Door Lock v1.0 allows attackers to create a cloned tag via brief physical proximity to the original tags, which results in an attacker gaining access to the perimeter.

Weak security in the transmitter of Digoo DG-HAMB Smart Home Security System v1.0 allows attackers to gain full access to the system via a code replay attack.

An issue found in WHOv.1.0.28, v.1.0.30, v.1.0.32 allows an attacker to cause a escalation of privileges via the TTMultiProvider component.

The Remote Keyless Entry (RKE) receiving unit on certain Honda vehicles through 2018 allows remote attackers to perform unlock operations and force a resynchronization after capturing five consecutive valid RKE signals over the radio, aka a RollBack attack. The attacker retains the ability to unlock indefinitely.

The Remote Keyless Entry (RKE) receiving unit on certain Mazda vehicles through 2020 allows remote attackers to perform unlock operations and force a resynchronization after capturing three consecutive valid key-fob signals over the radio, aka a RollBack attack. The attacker retains the ability to unlock indefinitely.

The Remote Keyless Entry (RKE) receiving unit on certain Nissan, Kia, and Hyundai vehicles through 2017 allows remote attackers to perform unlock operations and force a resynchronization after capturing two consecutive valid key fob signals over the radio, aka a RollBack attack. The attacker retains the ability to unlock indefinitely.

SWFTools commit 772e55a2 was discovered to contain a stack overflow via __sanitizer::StackDepotNode::hash(__sanitizer::StackTrace const&) at /sanitizer_common/sanitizer_stackdepot.cpp.

The remote keyless system on Honda Civic 2018 vehicles sends the same RF signal for each door-open request, which allows for a replay attack, a related issue to CVE-2019-20626.

The keyfob subsystem in Honda Civic 2012 vehicles allows a replay attack for unlocking. This is related to a non-expiring rolling code and counter resynchronization.

The S. Siedle & Soehne SG 150-0 Smart Gateway before 1.2.4 allows local privilege escalation via a race condition in logrotate. By using an exploit chain, an attacker with access to the network can get root access on the gateway.

The S. Siedle & Soehne SG 150-0 Smart Gateway before 1.2.4 allows remote code execution via the backup functionality in the web frontend. By using an exploit chain, an attacker with access to the network can get root access on the gateway.

Gira TKS-IP-Gateway 4.0.7.7 is vulnerable to authenticated remote code execution via the backup functionality of the web frontend. This can be combined with CVE-2020-10794 for remote root access.

Gira TKS-IP-Gateway 4.0.7.7 is vulnerable to unauthenticated path traversal that allows an attacker to download the application database. This can be combined with CVE-2020-10795 for remote root access.

The S. Siedle & Soehne SG 150-0 Smart Gateway before 1.2.4 has a passwordless ftp ssh user. By using an exploit chain, an attacker with access to the network can get root access on the gateway.

Rubetek SmartHome 2020 devices use unencrypted 433 MHz communication between controllers and beacons, allowing an attacker to sniff and spoof beacon requests remotely.