System vulnerabilities

In the Linux kernel, the following vulnerability has been resolved: media: bdisp: Add missing check for create_workqueue Add the check for the return value of the create_workqueue in order to avoid NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: drm/client: Fix memory leak in drm_client_modeset_probe When a new mode is set to modeset->mode, the previous mode should be freed. This fixes the following kmemleak report: drm_mode_duplicate+0x45/0x220 [drm] drm_client_modeset_probe+0x944/0xf50 [drm] __drm_fb_helper_initial_config_and_unlock+0xb4/0x2c0 [drm_kms_helper] drm_fbdev_client_hotplug+0x2bc/0x4d0 [drm_kms_helper] drm_client_register+0x169/0x240 [drm] ast_pci_probe+0x142/0x190 [ast] local_pci_probe+0xdc/0x180 work_for_cpu_fn+0x4e/0xa0 process_one_work+0x8b7/0x1540 worker_thread+0x70a/0xed0 kthread+0x29f/0x340 ret_from_fork+0x1f/0x30

In the Linux kernel, the following vulnerability has been resolved: usb: cdns3: Put the cdns set active part outside the spin lock The device may be scheduled during the resume process, so this cannot appear in atomic operations. Since pm_runtime_set_active will resume suppliers, put set active outside the spin lock, which is only used to protect the struct cdns data structure, otherwise the kernel will report the following warning: BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1163 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 651, name: sh preempt_count: 1, expected: 0 RCU nest depth: 0, expected: 0 CPU: 0 PID: 651 Comm: sh Tainted: G WC 6.1.20 #1 Hardware name: Freescale i.MX8QM MEK (DT) Call trace: dump_backtrace.part.0+0xe0/0xf0 show_stack+0x18/0x30 dump_stack_lvl+0x64/0x80 dump_stack+0x1c/0x38 __might_resched+0x1fc/0x240 __might_sleep+0x68/0xc0 __pm_runtime_resume+0x9c/0xe0 rpm_get_suppliers+0x68/0x1b0 __pm_runtime_set_status+0x298/0x560 cdns_resume+0xb0/0x1c0 cdns3_controller_resume.isra.0+0x1e0/0x250 cdns3_plat_resume+0x28/0x40

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Return the firmware result upon destroying QP/RQ Previously when destroying a QP/RQ, the result of the firmware destruction function was ignored and upper layers weren't informed about the failure. Which in turn could lead to various problems since when upper layer isn't aware of the failure it continues its operation thinking that the related QP/RQ was successfully destroyed while it actually wasn't, which could lead to the below kernel WARN. Currently, we return the correct firmware destruction status to upper layers which in case of the RQ would be mlx5_ib_destroy_wq() which was already capable of handling RQ destruction failure or in case of a QP to destroy_qp_common(), which now would actually warn upon qp destruction failure. WARNING: CPU: 3 PID: 995 at drivers/infiniband/core/rdma_core.c:940 uverbs_destroy_ufile_hw+0xcb/0xe0 [ib_uverbs] Modules linked in: xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi rdma_cm ib_umad ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core overlay mlx5_core fuse CPU: 3 PID: 995 Comm: python3 Not tainted 5.16.0-rc5+ #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:uverbs_destroy_ufile_hw+0xcb/0xe0 [ib_uverbs] Code: 41 5c 41 5d 41 5e e9 44 34 f0 e0 48 89 df e8 4c 77 ff ff 49 8b 86 10 01 00 00 48 85 c0 74 a1 4c 89 e7 ff d0 eb 9a 0f 0b eb c1 <0f> 0b be 04 00 00 00 48 89 df e8 b6 f6 ff ff e9 75 ff ff ff 90 0f RSP: 0018:ffff8881533e3e78 EFLAGS: 00010287 RAX: ffff88811b2cf3e0 RBX: ffff888106209700 RCX: 0000000000000000 RDX: ffff888106209780 RSI: ffff8881533e3d30 RDI: ffff888109b101a0 RBP: 0000000000000001 R08: ffff888127cb381c R09: 0de9890000000009 R10: ffff888127cb3800 R11: 0000000000000000 R12: ffff888106209780 R13: ffff888106209750 R14: ffff888100f20660 R15: 0000000000000000 FS: 00007f8be353b740(0000) GS:ffff88852c980000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8bd5b117c0 CR3: 000000012cd8a004 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ib_uverbs_close+0x1a/0x90 [ib_uverbs] __fput+0x82/0x230 task_work_run+0x59/0x90 exit_to_user_mode_prepare+0x138/0x140 syscall_exit_to_user_mode+0x1d/0x50 ? __x64_sys_close+0xe/0x40 do_syscall_64+0x4a/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f8be3ae0abb Code: 03 00 00 00 0f 05 48 3d 00 f0 ff ff 77 41 c3 48 83 ec 18 89 7c 24 0c e8 83 43 f9 ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 c1 43 f9 ff 8b 44 RSP: 002b:00007ffdb51909c0 EFLAGS: 00000293 ORIG_RAX: 0000000000000003 RAX: 0000000000000000 RBX: 0000557bb7f7c020 RCX: 00007f8be3ae0abb RDX: 0000557bb7c74010 RSI: 0000557bb7f14ca0 RDI: 0000000000000005 RBP: 0000557bb7fbd598 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000293 R12: 0000557bb7fbd5b8 R13: 0000557bb7fbd5a8 R14: 0000000000001000 R15: 0000557bb7f7c020 </TASK>

In the Linux kernel, the following vulnerability has been resolved: ext4: add bounds checking in get_max_inline_xattr_value_size() Normally the extended attributes in the inode body would have been checked when the inode is first opened, but if someone is writing to the block device while the file system is mounted, it's possible for the inode table to get corrupted. Add bounds checking to avoid reading beyond the end of allocated memory if this happens.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/dpu: check for null return of devm_kzalloc() in dpu_writeback_init() Because of the possilble failure of devm_kzalloc(), dpu_wb_conn might be NULL and will cause null pointer dereference later. Therefore, it might be better to check it and directly return -ENOMEM. Patchwork: https://patchwork.freedesktop.org/patch/512277/ [DB: fixed typo in commit message]

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix use-after-free KFENCE violation during sysfs firmware write During the sysfs firmware write process, a use-after-free read warning is logged from the lpfc_wr_object() routine: BUG: KFENCE: use-after-free read in lpfc_wr_object+0x235/0x310 [lpfc] Use-after-free read at 0x0000000000cf164d (in kfence-#111): lpfc_wr_object+0x235/0x310 [lpfc] lpfc_write_firmware.cold+0x206/0x30d [lpfc] lpfc_sli4_request_firmware_update+0xa6/0x100 [lpfc] lpfc_request_firmware_upgrade_store+0x66/0xb0 [lpfc] kernfs_fop_write_iter+0x121/0x1b0 new_sync_write+0x11c/0x1b0 vfs_write+0x1ef/0x280 ksys_write+0x5f/0xe0 do_syscall_64+0x59/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd The driver accessed wr_object pointer data, which was initialized into mailbox payload memory, after the mailbox object was released back to the mailbox pool. Fix by moving the mailbox free calls to the end of the routine ensuring that we don't reference internal mailbox memory after release.

In the Linux kernel, the following vulnerability has been resolved: drivers: staging: rtl8723bs: Fix locking in _rtw_join_timeout_handler() Commit 041879b12ddb ("drivers: staging: rtl8192bs: Fix deadlock in rtw_joinbss_event_prehandle()") besides fixing the deadlock also modified _rtw_join_timeout_handler() to use spin_[un]lock_irq() instead of spin_[un]lock_bh(). _rtw_join_timeout_handler() calls rtw_do_join() which takes pmlmepriv->scanned_queue.lock using spin_[un]lock_bh(). This spin_unlock_bh() call re-enables softirqs which triggers an oops in kernel/softirq.c: __local_bh_enable_ip() when it calls lockdep_assert_irqs_enabled(): [ 244.506087] WARNING: CPU: 2 PID: 0 at kernel/softirq.c:376 __local_bh_enable_ip+0xa6/0x100 ... [ 244.509022] Call Trace: [ 244.509048] <IRQ> [ 244.509100] _rtw_join_timeout_handler+0x134/0x170 [r8723bs] [ 244.509468] ? __pfx__rtw_join_timeout_handler+0x10/0x10 [r8723bs] [ 244.509772] ? __pfx__rtw_join_timeout_handler+0x10/0x10 [r8723bs] [ 244.510076] call_timer_fn+0x95/0x2a0 [ 244.510200] __run_timers.part.0+0x1da/0x2d0 This oops is causd by the switch to spin_[un]lock_irq() which disables the IRQs for the entire duration of _rtw_join_timeout_handler(). Disabling the IRQs is not necessary since all code taking this lock runs from either user contexts or from softirqs, switch back to spin_[un]lock_bh() to fix this.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Remove unused nvme_ls_waitq wait queue System crash when qla2x00_start_sp(sp) returns error code EGAIN and wake_up gets called for uninitialized wait queue sp->nvme_ls_waitq. qla2xxx [0000:37:00.1]-2121:5: Returning existing qpair of ffff8ae2c0513400 for idx=0 qla2xxx [0000:37:00.1]-700e:5: qla2x00_start_sp failed = 11 BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 PGD 0 P4D 0 Oops: 0000 [#1] SMP NOPTI Hardware name: HPE ProLiant DL360 Gen10/ProLiant DL360 Gen10, BIOS U32 09/03/2021 Workqueue: nvme-wq nvme_fc_connect_ctrl_work [nvme_fc] RIP: 0010:__wake_up_common+0x4c/0x190 RSP: 0018:ffff95f3e0cb7cd0 EFLAGS: 00010086 RAX: 0000000000000000 RBX: ffff8b08d3b26328 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffff8b08d3b26320 RBP: 0000000000000001 R08: 0000000000000000 R09: ffffffffffffffe8 R10: 0000000000000000 R11: ffff95f3e0cb7a60 R12: ffff95f3e0cb7d20 R13: 0000000000000003 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8b2fdf6c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000002f1e410002 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: __wake_up_common_lock+0x7c/0xc0 qla_nvme_ls_req+0x355/0x4c0 [qla2xxx] ? __nvme_fc_send_ls_req+0x260/0x380 [nvme_fc] ? nvme_fc_send_ls_req.constprop.42+0x1a/0x45 [nvme_fc] ? nvme_fc_connect_ctrl_work.cold.63+0x1e3/0xa7d [nvme_fc] Remove unused nvme_ls_waitq wait queue. nvme_ls_waitq logic was removed previously in the commits tagged Fixed: below.

In the Linux kernel, the following vulnerability has been resolved: misc: vmw_balloon: fix memory leak with using debugfs_lookup() When calling debugfs_lookup() the result must have dput() called on it, otherwise the memory will leak over time. To make things simpler, just call debugfs_lookup_and_remove() instead which handles all of the logic at once.

In the Linux kernel, the following vulnerability has been resolved: ubifs: Fix memory leak in ubifs_sysfs_init() When insmod ubifs.ko, a kmemleak reported as below: unreferenced object 0xffff88817fb1a780 (size 8): comm "insmod", pid 25265, jiffies 4295239702 (age 100.130s) hex dump (first 8 bytes): 75 62 69 66 73 00 ff ff ubifs... backtrace: [<ffffffff81b3fc4c>] slab_post_alloc_hook+0x9c/0x3c0 [<ffffffff81b44bf3>] __kmalloc_track_caller+0x183/0x410 [<ffffffff8198d3da>] kstrdup+0x3a/0x80 [<ffffffff8198d486>] kstrdup_const+0x66/0x80 [<ffffffff83989325>] kvasprintf_const+0x155/0x190 [<ffffffff83bf55bb>] kobject_set_name_vargs+0x5b/0x150 [<ffffffff83bf576b>] kobject_set_name+0xbb/0xf0 [<ffffffff8100204c>] do_one_initcall+0x14c/0x5a0 [<ffffffff8157e380>] do_init_module+0x1f0/0x660 [<ffffffff815857be>] load_module+0x6d7e/0x7590 [<ffffffff8158644f>] __do_sys_finit_module+0x19f/0x230 [<ffffffff815866b3>] __x64_sys_finit_module+0x73/0xb0 [<ffffffff88c98e85>] do_syscall_64+0x35/0x80 [<ffffffff88e00087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd When kset_register() failed, we should call kset_put to cleanup it.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwl3945: Add missing check for create_singlethread_workqueue Add the check for the return value of the create_singlethread_workqueue in order to avoid NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: ubifs: Free memory for tmpfile name When opening a ubifs tmpfile on an encrypted directory, function fscrypt_setup_filename allocates memory for the name that is to be stored in the directory entry, but after the name has been copied to the directory entry inode, the memory is not freed. When running kmemleak on it we see that it is registered as a leak. The report below is triggered by a simple program 'tmpfile' just opening a tmpfile: unreferenced object 0xffff88810178f380 (size 32): comm "tmpfile", pid 509, jiffies 4294934744 (age 1524.742s) backtrace: __kmem_cache_alloc_node __kmalloc fscrypt_setup_filename ubifs_tmpfile vfs_tmpfile path_openat Free this memory after it has been copied to the inode.

In the Linux kernel, the following vulnerability has been resolved: ALSA: hda: fix a possible null-pointer dereference due to data race in snd_hdac_regmap_sync() The variable codec->regmap is often protected by the lock codec->regmap_lock when is accessed. However, it is accessed without holding the lock when is accessed in snd_hdac_regmap_sync(): if (codec->regmap) In my opinion, this may be a harmful race, because if codec->regmap is set to NULL right after the condition is checked, a null-pointer dereference can occur in the called function regcache_sync(): map->lock(map->lock_arg); --> Line 360 in drivers/base/regmap/regcache.c To fix this possible null-pointer dereference caused by data race, the mutex_lock coverage is extended to protect the if statement as well as the function call to regcache_sync(). [ Note: the lack of the regmap_lock itself is harmless for the current codec driver implementations, as snd_hdac_regmap_sync() is only for PM runtime resume that is prohibited during the codec probe. But the change makes the whole code more consistent, so it's merged as is -- tiwai ]

In the Linux kernel, the following vulnerability has been resolved: clk: mediatek: mt8183: Add back SSPM related clocks This reverts commit 860690a93ef23b567f781c1b631623e27190f101. On the MT8183, the SSPM related clocks were removed claiming a lack of usage. This however causes some issues when the driver was converted to the new simple-probe mechanism. This mechanism allocates enough space for all the clocks defined in the clock driver, not the highest index in the DT binding. This leads to out-of-bound writes if their are holes in the DT binding or the driver (due to deprecated or unimplemented clocks). These errors can go unnoticed and cause memory corruption, leading to crashes in unrelated areas, or nothing at all. KASAN will detect them. Add the SSPM related clocks back to the MT8183 clock driver to fully implement the DT binding. The SSPM clocks are for the power management co-processor, and should never be turned off. They are marked as such.

In the Linux kernel, the following vulnerability has been resolved: Drivers: vmbus: Check for channel allocation before looking up relids relid2channel() assumes vmbus channel array to be allocated when called. However, in cases such as kdump/kexec, not all relids will be reset by the host. When the second kernel boots and if the guest receives a vmbus interrupt during vmbus driver initialization before vmbus_connect() is called, before it finishes, or if it fails, the vmbus interrupt service routine is called which in turn calls relid2channel() and can cause a null pointer dereference. Print a warning and error out in relid2channel() for a channel id that's invalid in the second kernel.

In the Linux kernel, the following vulnerability has been resolved: net: ena: fix shift-out-of-bounds in exponential backoff The ENA adapters on our instances occasionally reset. Once recently logged a UBSAN failure to console in the process: UBSAN: shift-out-of-bounds in build/linux/drivers/net/ethernet/amazon/ena/ena_com.c:540:13 shift exponent 32 is too large for 32-bit type 'unsigned int' CPU: 28 PID: 70012 Comm: kworker/u72:2 Kdump: loaded not tainted 5.15.117 Hardware name: Amazon EC2 c5d.9xlarge/, BIOS 1.0 10/16/2017 Workqueue: ena ena_fw_reset_device [ena] Call Trace: <TASK> dump_stack_lvl+0x4a/0x63 dump_stack+0x10/0x16 ubsan_epilogue+0x9/0x36 __ubsan_handle_shift_out_of_bounds.cold+0x61/0x10e ? __const_udelay+0x43/0x50 ena_delay_exponential_backoff_us.cold+0x16/0x1e [ena] wait_for_reset_state+0x54/0xa0 [ena] ena_com_dev_reset+0xc8/0x110 [ena] ena_down+0x3fe/0x480 [ena] ena_destroy_device+0xeb/0xf0 [ena] ena_fw_reset_device+0x30/0x50 [ena] process_one_work+0x22b/0x3d0 worker_thread+0x4d/0x3f0 ? process_one_work+0x3d0/0x3d0 kthread+0x12a/0x150 ? set_kthread_struct+0x50/0x50 ret_from_fork+0x22/0x30 </TASK> Apparently, the reset delays are getting so large they can trigger a UBSAN panic. Looking at the code, the current timeout is capped at 5000us. Using a base value of 100us, the current code will overflow after (1<<29). Even at values before 32, this function wraps around, perhaps unintentionally. Cap the value of the exponent used for this backoff at (1<<16) which is larger than currently necessary, but large enough to support bigger values in the future.

In the Linux kernel, the following vulnerability has been resolved: ubi: Fix unreferenced object reported by kmemleak in ubi_resize_volume() There is a memory leaks problem reported by kmemleak: unreferenced object 0xffff888102007a00 (size 128): comm "ubirsvol", pid 32090, jiffies 4298464136 (age 2361.231s) hex dump (first 32 bytes): ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ................ backtrace: [<ffffffff8176cecd>] __kmalloc+0x4d/0x150 [<ffffffffa02a9a36>] ubi_eba_create_table+0x76/0x170 [ubi] [<ffffffffa029764e>] ubi_resize_volume+0x1be/0xbc0 [ubi] [<ffffffffa02a3321>] ubi_cdev_ioctl+0x701/0x1850 [ubi] [<ffffffff81975d2d>] __x64_sys_ioctl+0x11d/0x170 [<ffffffff83c142a5>] do_syscall_64+0x35/0x80 [<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 This is due to a mismatch between create and destroy interfaces, and in detail that "new_eba_tbl" created by ubi_eba_create_table() but destroyed by kfree(), while will causing "new_eba_tbl->entries" not freed. Fix it by replacing kfree(new_eba_tbl) with ubi_eba_destroy_table(new_eba_tbl)

In the Linux kernel, the following vulnerability has been resolved: ext4: fix i_disksize exceeding i_size problem in paritally written case It is possible for i_disksize can exceed i_size, triggering a warning. generic_perform_write copied = iov_iter_copy_from_user_atomic(len) // copied < len ext4_da_write_end | ext4_update_i_disksize | new_i_size = pos + copied; | WRITE_ONCE(EXT4_I(inode)->i_disksize, newsize) // update i_disksize | generic_write_end | copied = block_write_end(copied, len) // copied = 0 | if (unlikely(copied < len)) | if (!PageUptodate(page)) | copied = 0; | if (pos + copied > inode->i_size) // return false if (unlikely(copied == 0)) goto again; if (unlikely(iov_iter_fault_in_readable(i, bytes))) { status = -EFAULT; break; } We get i_disksize greater than i_size here, which could trigger WARNING check 'i_size_read(inode) < EXT4_I(inode)->i_disksize' while doing dio: ext4_dio_write_iter iomap_dio_rw __iomap_dio_rw // return err, length is not aligned to 512 ext4_handle_inode_extension WARN_ON_ONCE(i_size_read(inode) < EXT4_I(inode)->i_disksize) // Oops WARNING: CPU: 2 PID: 2609 at fs/ext4/file.c:319 CPU: 2 PID: 2609 Comm: aa Not tainted 6.3.0-rc2 RIP: 0010:ext4_file_write_iter+0xbc7 Call Trace: vfs_write+0x3b1 ksys_write+0x77 do_syscall_64+0x39 Fix it by updating 'copied' value before updating i_disksize just like ext4_write_inline_data_end() does. A reproducer can be found in the buganizer link below.

In the Linux kernel, the following vulnerability has been resolved: block: ublk: make sure that block size is set correctly block size is one very key setting for block layer, and bad block size could panic kernel easily. Make sure that block size is set correctly. Meantime if ublk_validate_params() fails, clear ub->params so that disk is prevented from being added.

In the Linux kernel, the following vulnerability has been resolved: ASoC: fsl_mqs: move of_node_put() to the correct location of_node_put() should have been done directly after mqs_priv->regmap = syscon_node_to_regmap(gpr_np); otherwise it creates a reference leak on the success path. To fix this, of_node_put() is moved to the correct location, and change all the gotos to direct returns.

In the Linux kernel, the following vulnerability has been resolved: driver: soc: xilinx: fix memory leak in xlnx_add_cb_for_notify_event() The kfree() should be called when memory fails to be allocated for cb_data in xlnx_add_cb_for_notify_event(), otherwise there will be a memory leak, so add kfree() to fix it.

In the Linux kernel, the following vulnerability has been resolved: arm64: acpi: Fix possible memory leak of ffh_ctxt Allocated 'ffh_ctxt' memory leak is possible if the SMCCC version and conduit checks fail and -EOPNOTSUPP is returned without freeing the allocated memory. Fix the same by moving the allocation after the SMCCC version and conduit checks.

In the Linux kernel, the following vulnerability has been resolved: ubi: ensure that VID header offset + VID header size <= alloc, size Ensure that the VID header offset + VID header size does not exceed the allocated area to avoid slab OOB. BUG: KASAN: slab-out-of-bounds in crc32_body lib/crc32.c:111 [inline] BUG: KASAN: slab-out-of-bounds in crc32_le_generic lib/crc32.c:179 [inline] BUG: KASAN: slab-out-of-bounds in crc32_le_base+0x58c/0x626 lib/crc32.c:197 Read of size 4 at addr ffff88802bb36f00 by task syz-executor136/1555 CPU: 2 PID: 1555 Comm: syz-executor136 Tainted: G W 6.0.0-1868 #1 Hardware name: Red Hat KVM, BIOS 1.13.0-2.module+el8.3.0+7860+a7792d29 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x85/0xad lib/dump_stack.c:106 print_address_description mm/kasan/report.c:317 [inline] print_report.cold.13+0xb6/0x6bb mm/kasan/report.c:433 kasan_report+0xa7/0x11b mm/kasan/report.c:495 crc32_body lib/crc32.c:111 [inline] crc32_le_generic lib/crc32.c:179 [inline] crc32_le_base+0x58c/0x626 lib/crc32.c:197 ubi_io_write_vid_hdr+0x1b7/0x472 drivers/mtd/ubi/io.c:1067 create_vtbl+0x4d5/0x9c4 drivers/mtd/ubi/vtbl.c:317 create_empty_lvol drivers/mtd/ubi/vtbl.c:500 [inline] ubi_read_volume_table+0x67b/0x288a drivers/mtd/ubi/vtbl.c:812 ubi_attach+0xf34/0x1603 drivers/mtd/ubi/attach.c:1601 ubi_attach_mtd_dev+0x6f3/0x185e drivers/mtd/ubi/build.c:965 ctrl_cdev_ioctl+0x2db/0x347 drivers/mtd/ubi/cdev.c:1043 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x193/0x213 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3e/0x86 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0x0 RIP: 0033:0x7f96d5cf753d Code: RSP: 002b:00007fffd72206f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f96d5cf753d RDX: 0000000020000080 RSI: 0000000040186f40 RDI: 0000000000000003 RBP: 0000000000400cd0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000400be0 R13: 00007fffd72207e0 R14: 0000000000000000 R15: 0000000000000000 </TASK> Allocated by task 1555: kasan_save_stack+0x20/0x3d mm/kasan/common.c:38 kasan_set_track mm/kasan/common.c:45 [inline] set_alloc_info mm/kasan/common.c:437 [inline] ____kasan_kmalloc mm/kasan/common.c:516 [inline] __kasan_kmalloc+0x88/0xa3 mm/kasan/common.c:525 kasan_kmalloc include/linux/kasan.h:234 [inline] __kmalloc+0x138/0x257 mm/slub.c:4429 kmalloc include/linux/slab.h:605 [inline] ubi_alloc_vid_buf drivers/mtd/ubi/ubi.h:1093 [inline] create_vtbl+0xcc/0x9c4 drivers/mtd/ubi/vtbl.c:295 create_empty_lvol drivers/mtd/ubi/vtbl.c:500 [inline] ubi_read_volume_table+0x67b/0x288a drivers/mtd/ubi/vtbl.c:812 ubi_attach+0xf34/0x1603 drivers/mtd/ubi/attach.c:1601 ubi_attach_mtd_dev+0x6f3/0x185e drivers/mtd/ubi/build.c:965 ctrl_cdev_ioctl+0x2db/0x347 drivers/mtd/ubi/cdev.c:1043 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x193/0x213 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3e/0x86 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0x0 The buggy address belongs to the object at ffff88802bb36e00 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 0 bytes to the right of 256-byte region [ffff88802bb36e00, ffff88802bb36f00) The buggy address belongs to the physical page: page:00000000ea4d1263 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x2bb36 head:00000000ea4d1263 order:1 compound_mapcount:0 compound_pincount:0 flags: 0xfffffc0010200(slab|head|node=0|zone=1|lastcpupid=0x1fffff) raw: 000fffffc0010200 ffffea000066c300 dead000000000003 ffff888100042b40 raw: 0000000000000000 00000000001 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: clk: imx: clk-imxrt1050: fix memory leak in imxrt1050_clocks_probe Use devm_of_iomap() instead of of_iomap() to automatically handle the unused ioremap region. If any error occurs, regions allocated by kzalloc() will leak, but using devm_kzalloc() instead will automatically free the memory using devm_kfree(). Also, fix error handling of hws by adding unregister_hws label, which unregisters remaining hws when iomap failed.

In the Linux kernel, the following vulnerability has been resolved: drm/nouveau/disp: fix use-after-free in error handling of nouveau_connector_create We can't simply free the connector after calling drm_connector_init on it. We need to clean up the drm side first. It might not fix all regressions from commit 2b5d1c29f6c4 ("drm/nouveau/disp: PIOR DP uses GPIO for HPD, not PMGR AUX interrupts"), but at least it fixes a memory corruption in error handling related to that commit.

In the Linux kernel, the following vulnerability has been resolved: coresight: Fix memory leak in acpi_buffer->pointer There are memory leaks reported by kmemleak: ... unreferenced object 0xffff00213c141000 (size 1024): comm "systemd-udevd", pid 2123, jiffies 4294909467 (age 6062.160s) hex dump (first 32 bytes): 04 00 00 00 02 00 00 00 18 10 14 3c 21 00 ff ff ...........<!... 00 00 00 00 00 00 00 00 03 00 00 00 10 00 00 00 ................ backtrace: [<000000004b7c9001>] __kmem_cache_alloc_node+0x2f8/0x348 [<00000000b0fc7ceb>] __kmalloc+0x58/0x108 [<0000000064ff4695>] acpi_os_allocate+0x2c/0x68 [<000000007d57d116>] acpi_ut_initialize_buffer+0x54/0xe0 [<0000000024583908>] acpi_evaluate_object+0x388/0x438 [<0000000017b2e72b>] acpi_evaluate_object_typed+0xe8/0x240 [<000000005df0eac2>] coresight_get_platform_data+0x1b4/0x988 [coresight] ... The ACPI buffer memory (buf.pointer) should be freed. But the buffer is also used after returning from acpi_get_dsd_graph(). Move the temporary variables buf to acpi_coresight_parse_graph(), and free it before the function return to prevent memory leak.

In the Linux kernel, the following vulnerability has been resolved: ovl: fix null pointer dereference in ovl_permission() Following process: P1 P2 path_lookupat link_path_walk inode_permission ovl_permission ovl_i_path_real(inode, &realpath) path->dentry = ovl_i_dentry_upper(inode) drop_cache __dentry_kill(ovl_dentry) iput(ovl_inode) ovl_destroy_inode(ovl_inode) dput(oi->__upperdentry) dentry_kill(upperdentry) dentry_unlink_inode upperdentry->d_inode = NULL realinode = d_inode(realpath.dentry) // return NULL inode_permission(realinode) inode->i_sb // NULL pointer dereference , will trigger an null pointer dereference at realinode: [ 335.664979] BUG: kernel NULL pointer dereference, address: 0000000000000002 [ 335.668032] CPU: 0 PID: 2592 Comm: ls Not tainted 6.3.0 [ 335.669956] RIP: 0010:inode_permission+0x33/0x2c0 [ 335.678939] Call Trace: [ 335.679165] <TASK> [ 335.679371] ovl_permission+0xde/0x320 [ 335.679723] inode_permission+0x15e/0x2c0 [ 335.680090] link_path_walk+0x115/0x550 [ 335.680771] path_lookupat.isra.0+0xb2/0x200 [ 335.681170] filename_lookup+0xda/0x240 [ 335.681922] vfs_statx+0xa6/0x1f0 [ 335.682233] vfs_fstatat+0x7b/0xb0 Fetch a reproducer in [Link]. Use the helper ovl_i_path_realinode() to get realinode and then do non-nullptr checking.

In the Linux kernel, the following vulnerability has been resolved: VMCI: check context->notify_page after call to get_user_pages_fast() to avoid GPF The call to get_user_pages_fast() in vmci_host_setup_notify() can return NULL context->notify_page causing a GPF. To avoid GPF check if context->notify_page == NULL and return error if so. general protection fault, probably for non-canonical address 0xe0009d1000000060: 0000 [#1] PREEMPT SMP KASAN NOPTI KASAN: maybe wild-memory-access in range [0x0005088000000300- 0x0005088000000307] CPU: 2 PID: 26180 Comm: repro_34802241 Not tainted 6.1.0-rc4 #1 Hardware name: Red Hat KVM, BIOS 1.15.0-2.module+el8.6.0 04/01/2014 RIP: 0010:vmci_ctx_check_signal_notify+0x91/0xe0 Call Trace: <TASK> vmci_host_unlocked_ioctl+0x362/0x1f40 __x64_sys_ioctl+0x1a1/0x230 do_syscall_64+0x3a/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix possible underflow for displays with large vblank [Why] Underflow observed when using a display with a large vblank region and low refresh rate [How] Simplify calculation of vblank_nom Increase value for VBlankNomDefaultUS to 800us

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: check S1G action frame size Before checking the action code, check that it even exists in the frame.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix scheduling while atomic in decompression path [ 16.945668][ C0] Call trace: [ 16.945678][ C0] dump_backtrace+0x110/0x204 [ 16.945706][ C0] dump_stack_lvl+0x84/0xbc [ 16.945735][ C0] __schedule_bug+0xb8/0x1ac [ 16.945756][ C0] __schedule+0x724/0xbdc [ 16.945778][ C0] schedule+0x154/0x258 [ 16.945793][ C0] bit_wait_io+0x48/0xa4 [ 16.945808][ C0] out_of_line_wait_on_bit+0x114/0x198 [ 16.945824][ C0] __sync_dirty_buffer+0x1f8/0x2e8 [ 16.945853][ C0] __f2fs_commit_super+0x140/0x1f4 [ 16.945881][ C0] f2fs_commit_super+0x110/0x28c [ 16.945898][ C0] f2fs_handle_error+0x1f4/0x2f4 [ 16.945917][ C0] f2fs_decompress_cluster+0xc4/0x450 [ 16.945942][ C0] f2fs_end_read_compressed_page+0xc0/0xfc [ 16.945959][ C0] f2fs_handle_step_decompress+0x118/0x1cc [ 16.945978][ C0] f2fs_read_end_io+0x168/0x2b0 [ 16.945993][ C0] bio_endio+0x25c/0x2c8 [ 16.946015][ C0] dm_io_dec_pending+0x3e8/0x57c [ 16.946052][ C0] clone_endio+0x134/0x254 [ 16.946069][ C0] bio_endio+0x25c/0x2c8 [ 16.946084][ C0] blk_update_request+0x1d4/0x478 [ 16.946103][ C0] scsi_end_request+0x38/0x4cc [ 16.946129][ C0] scsi_io_completion+0x94/0x184 [ 16.946147][ C0] scsi_finish_command+0xe8/0x154 [ 16.946164][ C0] scsi_complete+0x90/0x1d8 [ 16.946181][ C0] blk_done_softirq+0xa4/0x11c [ 16.946198][ C0] _stext+0x184/0x614 [ 16.946214][ C0] __irq_exit_rcu+0x78/0x144 [ 16.946234][ C0] handle_domain_irq+0xd4/0x154 [ 16.946260][ C0] gic_handle_irq.33881+0x5c/0x27c [ 16.946281][ C0] call_on_irq_stack+0x40/0x70 [ 16.946298][ C0] do_interrupt_handler+0x48/0xa4 [ 16.946313][ C0] el1_interrupt+0x38/0x68 [ 16.946346][ C0] el1h_64_irq_handler+0x20/0x30 [ 16.946362][ C0] el1h_64_irq+0x78/0x7c [ 16.946377][ C0] finish_task_switch+0xc8/0x3d8 [ 16.946394][ C0] __schedule+0x600/0xbdc [ 16.946408][ C0] preempt_schedule_common+0x34/0x5c [ 16.946423][ C0] preempt_schedule+0x44/0x48 [ 16.946438][ C0] process_one_work+0x30c/0x550 [ 16.946456][ C0] worker_thread+0x414/0x8bc [ 16.946472][ C0] kthread+0x16c/0x1e0 [ 16.946486][ C0] ret_from_fork+0x10/0x20

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_ffa: Fix FFA device names for logical partitions Each physical partition can provide multiple services each with UUID. Each such service can be presented as logical partition with a unique combination of VM ID and UUID. The number of distinct UUID in a system will be less than or equal to the number of logical partitions. However, currently it fails to register more than one logical partition or service within a physical partition as the device name contains only VM ID while both VM ID and UUID are maintained in the partition information. The kernel complains with the below message: | sysfs: cannot create duplicate filename '/devices/arm-ffa-8001' | CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8 | Hardware name: FVP Base RevC (DT) | Call trace: | dump_backtrace+0xf8/0x118 | show_stack+0x18/0x24 | dump_stack_lvl+0x50/0x68 | dump_stack+0x18/0x24 | sysfs_create_dir_ns+0xe0/0x13c | kobject_add_internal+0x220/0x3d4 | kobject_add+0x94/0x100 | device_add+0x144/0x5d8 | device_register+0x20/0x30 | ffa_device_register+0x88/0xd8 | ffa_setup_partitions+0x108/0x1b8 | ffa_init+0x2ec/0x3a4 | do_one_initcall+0xcc/0x240 | do_initcall_level+0x8c/0xac | do_initcalls+0x54/0x94 | do_basic_setup+0x1c/0x28 | kernel_init_freeable+0x100/0x16c | kernel_init+0x20/0x1a0 | ret_from_fork+0x10/0x20 | kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to | register things with the same name in the same directory. | arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17 | ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001 By virtue of being random enough to avoid collisions when generated in a distributed system, there is no way to compress UUID keys to the number of bits required to identify each. We can eliminate '-' in the name but it is not worth eliminating 4 bytes and add unnecessary logic for doing that. Also v1.0 doesn't provide the UUID of the partitions which makes it hard to use the same for the device name. So to keep it simple, let us alloc an ID using ida_alloc() and append the same to "arm-ffa" to make up a unique device name. Also stash the id value in ffa_dev to help freeing the ID later when the device is destroyed.

In the Linux kernel, the following vulnerability has been resolved: firmware: stratix10-svc: Fix a potential resource leak in svc_create_memory_pool() svc_create_memory_pool() is only called from stratix10_svc_drv_probe(). Most of resources in the probe are managed, but not this memremap() call. There is also no memunmap() call in the file. So switch to devm_memremap() to avoid a resource leak.

In the Linux kernel, the following vulnerability has been resolved: cacheinfo: Fix shared_cpu_map to handle shared caches at different levels The cacheinfo sets up the shared_cpu_map by checking whether the caches with the same index are shared between CPUs. However, this will trigger slab-out-of-bounds access if the CPUs do not have the same cache hierarchy. Another problem is the mismatched shared_cpu_map when the shared cache does not have the same index between CPUs. CPU0 I D L3 index 0 1 2 x ^ ^ ^ ^ index 0 1 2 3 CPU1 I D L2 L3 This patch checks each cache is shared with all caches on other CPUs.

In the Linux kernel, the following vulnerability has been resolved: HID: nvidia-shield: Reference hid_device devm allocation of input_dev name Use hid_device for devm allocation of the input_dev name to avoid a use-after-free. input_unregister_device would trigger devres cleanup of all resources associated with the input_dev, free-ing the name. The name would subsequently be used in a uevent fired at the end of unregistering the input_dev.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: use RCU for hci_conn_params and iterate safely in hci_sync hci_update_accept_list_sync iterates over hdev->pend_le_conns and hdev->pend_le_reports, and waits for controller events in the loop body, without holding hdev lock. Meanwhile, these lists and the items may be modified e.g. by le_scan_cleanup. This can invalidate the list cursor or any other item in the list, resulting to invalid behavior (eg use-after-free). Use RCU for the hci_conn_params action lists. Since the loop bodies in hci_sync block and we cannot use RCU or hdev->lock for the whole loop, copy list items first and then iterate on the copy. Only the flags field is written from elsewhere, so READ_ONCE/WRITE_ONCE should guarantee we read valid values. Free params everywhere with hci_conn_params_free so the cleanup is guaranteed to be done properly. This fixes the following, which can be triggered e.g. by BlueZ new mgmt-tester case "Add + Remove Device Nowait - Success", or by changing hci_le_set_cig_params to always return false, and running iso-tester: ================================================================== BUG: KASAN: slab-use-after-free in hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) Read of size 8 at addr ffff888001265018 by task kworker/u3:0/32 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 Workqueue: hci0 hci_cmd_sync_work Call Trace: <TASK> dump_stack_lvl (./arch/x86/include/asm/irqflags.h:134 lib/dump_stack.c:107) print_report (mm/kasan/report.c:320 mm/kasan/report.c:430) ? __virt_addr_valid (./include/linux/mmzone.h:1915 ./include/linux/mmzone.h:2011 arch/x86/mm/physaddr.c:65) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) kasan_report (mm/kasan/report.c:538) ? hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2536 net/bluetooth/hci_sync.c:2723 net/bluetooth/hci_sync.c:2841) ? __pfx_hci_update_passive_scan_sync (net/bluetooth/hci_sync.c:2780) ? mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_lock (kernel/locking/mutex.c:282) ? __pfx_mutex_unlock (kernel/locking/mutex.c:538) ? __pfx_update_passive_scan_sync (net/bluetooth/hci_sync.c:2861) hci_cmd_sync_work (net/bluetooth/hci_sync.c:306) process_one_work (./arch/x86/include/asm/preempt.h:27 kernel/workqueue.c:2399) worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2538) ? __pfx_worker_thread (kernel/workqueue.c:2480) kthread (kernel/kthread.c:376) ? __pfx_kthread (kernel/kthread.c:331) ret_from_fork (arch/x86/entry/entry_64.S:314) </TASK> Allocated by task 31: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) __kasan_kmalloc (mm/kasan/common.c:374 mm/kasan/common.c:383) hci_conn_params_add (./include/linux/slab.h:580 ./include/linux/slab.h:720 net/bluetooth/hci_core.c:2277) hci_connect_le_scan (net/bluetooth/hci_conn.c:1419 net/bluetooth/hci_conn.c:1589) hci_connect_cis (net/bluetooth/hci_conn.c:2266) iso_connect_cis (net/bluetooth/iso.c:390) iso_sock_connect (net/bluetooth/iso.c:899) __sys_connect (net/socket.c:2003 net/socket.c:2020) __x64_sys_connect (net/socket.c:2027) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) Freed by task 15: kasan_save_stack (mm/kasan/common.c:46) kasan_set_track (mm/kasan/common.c:52) kasan_save_free_info (mm/kasan/generic.c:523) __kasan_slab_free (mm/kasan/common.c:238 mm/kasan/common.c:200 mm/kasan/common.c:244) __kmem_cache_free (mm/slub.c:1807 mm/slub.c:3787 mm/slub.c:3800) hci_conn_params_del (net/bluetooth/hci_core.c:2323) le_scan_cleanup (net/bluetooth/hci_conn.c:202) process_one_work (./arch/x86/include/asm/preempt. ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: pcie: fix NULL pointer dereference in iwl_pcie_irq_rx_msix_handler() rxq can be NULL only when trans_pcie->rxq is NULL and entry->entry is zero. For the case when entry->entry is not equal to 0, rxq won't be NULL even if trans_pcie->rxq is NULL. Modify checker to check for trans_pcie->rxq.

In the Linux kernel, the following vulnerability has been resolved: firmware: dmi-sysfs: Fix null-ptr-deref in dmi_sysfs_register_handle KASAN reported a null-ptr-deref error: KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f] CPU: 0 PID: 1373 Comm: modprobe Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) RIP: 0010:dmi_sysfs_entry_release ... Call Trace: <TASK> kobject_put dmi_sysfs_register_handle (drivers/firmware/dmi-sysfs.c:540) dmi_sysfs dmi_decode_table (drivers/firmware/dmi_scan.c:133) dmi_walk (drivers/firmware/dmi_scan.c:1115) dmi_sysfs_init (drivers/firmware/dmi-sysfs.c:149) dmi_sysfs do_one_initcall (init/main.c:1296) ... Kernel panic - not syncing: Fatal exception Kernel Offset: 0x4000000 from 0xffffffff81000000 ---[ end Kernel panic - not syncing: Fatal exception ]--- It is because previous patch added kobject_put() to release the memory which will call dmi_sysfs_entry_release() and list_del(). However, list_add_tail(entry->list) is called after the error block, so the list_head is uninitialized and cannot be deleted. Move error handling to after list_add_tail to fix this.

In the Linux kernel, the following vulnerability has been resolved: clk: imx: clk-imx8mn: fix memory leak in imx8mn_clocks_probe Use devm_of_iomap() instead of of_iomap() to automatically handle the unused ioremap region. If any error occurs, regions allocated by kzalloc() will leak, but using devm_kzalloc() instead will automatically free the memory using devm_kfree().

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: install stub fence into potential unused fence pointers When using cpu to update page tables, vm update fences are unused. Install stub fence into these fence pointers instead of NULL to avoid NULL dereference when calling dma_fence_wait() on them.

In the Linux kernel, the following vulnerability has been resolved: btrfs: set_page_extent_mapped after read_folio in btrfs_cont_expand While trying to get the subpage blocksize tests running, I hit the following panic on generic/476 assertion failed: PagePrivate(page) && page->private, in fs/btrfs/subpage.c:229 kernel BUG at fs/btrfs/subpage.c:229! Internal error: Oops - BUG: 00000000f2000800 [#1] SMP CPU: 1 PID: 1453 Comm: fsstress Not tainted 6.4.0-rc7+ #12 Hardware name: QEMU KVM Virtual Machine, BIOS edk2-20230301gitf80f052277c8-26.fc38 03/01/2023 pstate: 61400005 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) pc : btrfs_subpage_assert+0xbc/0xf0 lr : btrfs_subpage_assert+0xbc/0xf0 Call trace: btrfs_subpage_assert+0xbc/0xf0 btrfs_subpage_clear_checked+0x38/0xc0 btrfs_page_clear_checked+0x48/0x98 btrfs_truncate_block+0x5d0/0x6a8 btrfs_cont_expand+0x5c/0x528 btrfs_write_check.isra.0+0xf8/0x150 btrfs_buffered_write+0xb4/0x760 btrfs_do_write_iter+0x2f8/0x4b0 btrfs_file_write_iter+0x1c/0x30 do_iter_readv_writev+0xc8/0x158 do_iter_write+0x9c/0x210 vfs_iter_write+0x24/0x40 iter_file_splice_write+0x224/0x390 direct_splice_actor+0x38/0x68 splice_direct_to_actor+0x12c/0x260 do_splice_direct+0x90/0xe8 generic_copy_file_range+0x50/0x90 vfs_copy_file_range+0x29c/0x470 __arm64_sys_copy_file_range+0xcc/0x498 invoke_syscall.constprop.0+0x80/0xd8 do_el0_svc+0x6c/0x168 el0_svc+0x50/0x1b0 el0t_64_sync_handler+0x114/0x120 el0t_64_sync+0x194/0x198 This happens because during btrfs_cont_expand we'll get a page, set it as mapped, and if it's not Uptodate we'll read it. However between the read and re-locking the page we could have called release_folio() on the page, but left the page in the file mapping. release_folio() can clear the page private, and thus further down we blow up when we go to modify the subpage bits. Fix this by putting the set_page_extent_mapped() after the read. This is safe because read_folio() will call set_page_extent_mapped() before it does the read, and then if we clear page private but leave it on the mapping we're completely safe re-setting set_page_extent_mapped(). With this patch I can now run generic/476 without panicing.

In the Linux kernel, the following vulnerability has been resolved: cifs: fix DFS traversal oops without CONFIG_CIFS_DFS_UPCALL When compiled with CONFIG_CIFS_DFS_UPCALL disabled, cifs_dfs_d_automount is NULL. cifs.ko logic for mapping CIFS_FATTR_DFS_REFERRAL attributes to S_AUTOMOUNT and corresponding dentry flags is retained regardless of CONFIG_CIFS_DFS_UPCALL, leading to a NULL pointer dereference in VFS follow_automount() when traversing a DFS referral link: BUG: kernel NULL pointer dereference, address: 0000000000000000 ... Call Trace: <TASK> __traverse_mounts+0xb5/0x220 ? cifs_revalidate_mapping+0x65/0xc0 [cifs] step_into+0x195/0x610 ? lookup_fast+0xe2/0xf0 path_lookupat+0x64/0x140 filename_lookup+0xc2/0x140 ? __create_object+0x299/0x380 ? kmem_cache_alloc+0x119/0x220 ? user_path_at_empty+0x31/0x50 user_path_at_empty+0x31/0x50 __x64_sys_chdir+0x2a/0xd0 ? exit_to_user_mode_prepare+0xca/0x100 do_syscall_64+0x42/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc This fix adds an inline cifs_dfs_d_automount() {return -EREMOTE} handler when CONFIG_CIFS_DFS_UPCALL is disabled. An alternative would be to avoid flagging S_AUTOMOUNT, etc. without CONFIG_CIFS_DFS_UPCALL. This approach was chosen as it provides more control over the error path.

In the Linux kernel, the following vulnerability has been resolved: scsi: storvsc: Fix handling of virtual Fibre Channel timeouts Hyper-V provides the ability to connect Fibre Channel LUNs to the host system and present them in a guest VM as a SCSI device. I/O to the vFC device is handled by the storvsc driver. The storvsc driver includes a partial integration with the FC transport implemented in the generic portion of the Linux SCSI subsystem so that FC attributes can be displayed in /sys. However, the partial integration means that some aspects of vFC don't work properly. Unfortunately, a full and correct integration isn't practical because of limitations in what Hyper-V provides to the guest. In particular, in the context of Hyper-V storvsc, the FC transport timeout function fc_eh_timed_out() causes a kernel panic because it can't find the rport and dereferences a NULL pointer. The original patch that added the call from storvsc_eh_timed_out() to fc_eh_timed_out() is faulty in this regard. In many cases a timeout is due to a transient condition, so the situation can be improved by just continuing to wait like with other I/O requests issued by storvsc, and avoiding the guaranteed panic. For a permanent failure, continuing to wait may result in a hung thread instead of a panic, which again may be better. So fix the panic by removing the storvsc call to fc_eh_timed_out(). This allows storvsc to keep waiting for a response. The change has been tested by users who experienced a panic in fc_eh_timed_out() due to transient timeouts, and it solves their problem. In the future we may want to deprecate the vFC functionality in storvsc since it can't be fully fixed. But it has current users for whom it is working well enough, so it should probably stay for a while longer.

In the Linux kernel, the following vulnerability has been resolved: media: pci: tw68: Fix null-ptr-deref bug in buf prepare and finish When the driver calls tw68_risc_buffer() to prepare the buffer, the function call dma_alloc_coherent may fail, resulting in a empty buffer buf->cpu. Later when we free the buffer or access the buffer, null ptr deref is triggered. This bug is similar to the following one: https://git.linuxtv.org/media_stage.git/commit/?id=2b064d91440b33fba5b452f2d1b31f13ae911d71. We believe the bug can be also dynamically triggered from user side. Similarly, we fix this by checking the return value of tw68_risc_buffer() and the value of buf->cpu before buffer free.

In the Linux kernel, the following vulnerability has been resolved: btrfs: add handling for RAID1C23/DUP to btrfs_reduce_alloc_profile Callers of `btrfs_reduce_alloc_profile` expect it to return exactly one allocation profile flag, and failing to do so may ultimately result in a WARN_ON and remount-ro when allocating new blocks, like the below transaction abort on 6.1. `btrfs_reduce_alloc_profile` has two ways of determining the profile, first it checks if a conversion balance is currently running and uses the profile we're converting to. If no balance is currently running, it returns the max-redundancy profile which at least one block in the selected block group has. This works by simply checking each known allocation profile bit in redundancy order. However, `btrfs_reduce_alloc_profile` has not been updated as new flags have been added - first with the `DUP` profile and later with the RAID1C34 profiles. Because of the way it checks, if we have blocks with different profiles and at least one is known, that profile will be selected. However, if none are known we may return a flag set with multiple allocation profiles set. This is currently only possible when a balance from one of the three unhandled profiles to another of the unhandled profiles is canceled after allocating at least one block using the new profile. In that case, a transaction abort like the below will occur and the filesystem will need to be mounted with -o skip_balance to get it mounted rw again (but the balance cannot be resumed without a similar abort). [770.648] ------------[ cut here ]------------ [770.648] BTRFS: Transaction aborted (error -22) [770.648] WARNING: CPU: 43 PID: 1159593 at fs/btrfs/extent-tree.c:4122 find_free_extent+0x1d94/0x1e00 [btrfs] [770.648] CPU: 43 PID: 1159593 Comm: btrfs Tainted: G W 6.1.0-0.deb11.7-powerpc64le #1 Debian 6.1.20-2~bpo11+1a~test [770.648] Hardware name: T2P9D01 REV 1.00 POWER9 0x4e1202 opal:skiboot-bc106a0 PowerNV [770.648] NIP: c00800000f6784fc LR: c00800000f6784f8 CTR: c000000000d746c0 [770.648] REGS: c000200089afe9a0 TRAP: 0700 Tainted: G W (6.1.0-0.deb11.7-powerpc64le Debian 6.1.20-2~bpo11+1a~test) [770.648] MSR: 9000000002029033 <SF,HV,VEC,EE,ME,IR,DR,RI,LE> CR: 28848282 XER: 20040000 [770.648] CFAR: c000000000135110 IRQMASK: 0 GPR00: c00800000f6784f8 c000200089afec40 c00800000f7ea800 0000000000000026 GPR04: 00000001004820c2 c000200089afea00 c000200089afe9f8 0000000000000027 GPR08: c000200ffbfe7f98 c000000002127f90 ffffffffffffffd8 0000000026d6a6e8 GPR12: 0000000028848282 c000200fff7f3800 5deadbeef0000122 c00000002269d000 GPR16: c0002008c7797c40 c000200089afef17 0000000000000000 0000000000000000 GPR20: 0000000000000000 0000000000000001 c000200008bc5a98 0000000000000001 GPR24: 0000000000000000 c0000003c73088d0 c000200089afef17 c000000016d3a800 GPR28: c0000003c7308800 c00000002269d000 ffffffffffffffea 0000000000000001 [770.648] NIP [c00800000f6784fc] find_free_extent+0x1d94/0x1e00 [btrfs] [770.648] LR [c00800000f6784f8] find_free_extent+0x1d90/0x1e00 [btrfs] [770.648] Call Trace: [770.648] [c000200089afec40] [c00800000f6784f8] find_free_extent+0x1d90/0x1e00 [btrfs] (unreliable) [770.648] [c000200089afed30] [c00800000f681398] btrfs_reserve_extent+0x1a0/0x2f0 [btrfs] [770.648] [c000200089afeea0] [c00800000f681bf0] btrfs_alloc_tree_block+0x108/0x670 [btrfs] [770.648] [c000200089afeff0] [c00800000f66bd68] __btrfs_cow_block+0x170/0x850 [btrfs] [770.648] [c000200089aff100] [c00800000f66c58c] btrfs_cow_block+0x144/0x288 [btrfs] [770.648] [c000200089aff1b0] [c00800000f67113c] btrfs_search_slot+0x6b4/0xcb0 [btrfs] [770.648] [c000200089aff2a0] [c00800000f679f60] lookup_inline_extent_backref+0x128/0x7c0 [btrfs] [770.648] [c000200089aff3b0] [c00800000f67b338] lookup_extent_backref+0x70/0x190 [btrfs] [770.648] [c000200089aff470] [c00800000f67b54c] __btrfs_free_extent+0xf4/0x1490 [btrfs] [770.648] [ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: nfsd: call op_release, even when op_func returns an error For ops with "trivial" replies, nfsd4_encode_operation will shortcut most of the encoding work and skip to just marshalling up the status. One of the things it skips is calling op_release. This could cause a memory leak in the layoutget codepath if there is an error at an inopportune time. Have the compound processing engine always call op_release, even when op_func sets an error in op->status. With this change, we also need nfsd4_block_get_device_info_scsi to set the gd_device pointer to NULL on error to avoid a double free.

In the Linux kernel, the following vulnerability has been resolved: xsk: check IFF_UP earlier in Tx path Xsk Tx can be triggered via either sendmsg() or poll() syscalls. These two paths share a call to common function xsk_xmit() which has two sanity checks within. A pseudo code example to show the two paths: __xsk_sendmsg() : xsk_poll(): if (unlikely(!xsk_is_bound(xs))) if (unlikely(!xsk_is_bound(xs))) return -ENXIO; return mask; if (unlikely(need_wait)) (...) return -EOPNOTSUPP; xsk_xmit() mark napi id (...) xsk_xmit() xsk_xmit(): if (unlikely(!(xs->dev->flags & IFF_UP))) return -ENETDOWN; if (unlikely(!xs->tx)) return -ENOBUFS; As it can be observed above, in sendmsg() napi id can be marked on interface that was not brought up and this causes a NULL ptr dereference: [31757.505631] BUG: kernel NULL pointer dereference, address: 0000000000000018 [31757.512710] #PF: supervisor read access in kernel mode [31757.517936] #PF: error_code(0x0000) - not-present page [31757.523149] PGD 0 P4D 0 [31757.525726] Oops: 0000 [#1] PREEMPT SMP NOPTI [31757.530154] CPU: 26 PID: 95641 Comm: xdpsock Not tainted 6.2.0-rc5+ #40 [31757.536871] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [31757.547457] RIP: 0010:xsk_sendmsg+0xde/0x180 [31757.551799] Code: 00 75 a2 48 8b 00 a8 04 75 9b 84 d2 74 69 8b 85 14 01 00 00 85 c0 75 1b 48 8b 85 28 03 00 00 48 8b 80 98 00 00 00 48 8b 40 20 <8b> 40 18 89 85 14 01 00 00 8b bd 14 01 00 00 81 ff 00 01 00 00 0f [31757.570840] RSP: 0018:ffffc90034f27dc0 EFLAGS: 00010246 [31757.576143] RAX: 0000000000000000 RBX: ffffc90034f27e18 RCX: 0000000000000000 [31757.583389] RDX: 0000000000000001 RSI: ffffc90034f27e18 RDI: ffff88984cf3c100 [31757.590631] RBP: ffff88984714a800 R08: ffff88984714a800 R09: 0000000000000000 [31757.597877] R10: 0000000000000001 R11: 0000000000000000 R12: 00000000fffffffa [31757.605123] R13: 0000000000000000 R14: 0000000000000003 R15: 0000000000000000 [31757.612364] FS: 00007fb4c5931180(0000) GS:ffff88afdfa00000(0000) knlGS:0000000000000000 [31757.620571] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [31757.626406] CR2: 0000000000000018 CR3: 000000184b41c003 CR4: 00000000007706e0 [31757.633648] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [31757.640894] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [31757.648139] PKRU: 55555554 [31757.650894] Call Trace: [31757.653385] <TASK> [31757.655524] sock_sendmsg+0x8f/0xa0 [31757.659077] ? sockfd_lookup_light+0x12/0x70 [31757.663416] __sys_sendto+0xfc/0x170 [31757.667051] ? do_sched_setscheduler+0xdb/0x1b0 [31757.671658] __x64_sys_sendto+0x20/0x30 [31757.675557] do_syscall_64+0x38/0x90 [31757.679197] entry_SYSCALL_64_after_hwframe+0x72/0xdc [31757.687969] Code: 8e f6 ff 44 8b 4c 24 2c 4c 8b 44 24 20 41 89 c4 44 8b 54 24 28 48 8b 54 24 18 b8 2c 00 00 00 48 8b 74 24 10 8b 7c 24 08 0f 05 <48> 3d 00 f0 ff ff 77 3a 44 89 e7 48 89 44 24 08 e8 b5 8e f6 ff 48 [31757.707007] RSP: 002b:00007ffd49c73c70 EFLAGS: 00000293 ORIG_RAX: 000000000000002c [31757.714694] RAX: ffffffffffffffda RBX: 000055a996565380 RCX: 00007fb4c5727c16 [31757.721939] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 [31757.729184] RBP: 0000000000000040 R08: 0000000000000000 R09: 0000000000000000 [31757.736429] R10: 0000000000000040 R11: 0000000000000293 R12: 0000000000000000 [31757.743673] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [31757.754940] </TASK> To fix this, let's make xsk_xmit a function that will be responsible for generic Tx, where RCU is handled accordingly and pull out sanity checks and xs->zc handling. Populate sanity checks to __xsk_sendmsg() and xsk_poll().

In the Linux kernel, the following vulnerability has been resolved: drm/msm/mdp5: Add check for kzalloc As kzalloc may fail and return NULL pointer, it should be better to check the return value in order to avoid the NULL pointer dereference. Patchwork: https://patchwork.freedesktop.org/patch/514154/

In the Linux kernel, the following vulnerability has been resolved: thermal/drivers/hisi: Drop second sensor hi3660 The commit 74c8e6bffbe1 ("driver core: Add __alloc_size hint to devm allocators") exposes a panic "BRK handler: Fatal exception" on the hi3660_thermal_probe funciton. This is because the function allocates memory for only one sensors array entry, but tries to fill up a second one. Fix this by removing the unneeded second access.