Linux vulnerabilities

In the Linux kernel, the following vulnerability has been resolved: net: usb: cdc_ncm: add ndpoffset to NDP32 nframes bounds check The same bounds-check bug fixed for NDP16 in the previous patch also exists in cdc_ncm_rx_verify_ndp32(). The DPE array size is validated against the total skb length without accounting for ndpoffset, allowing out-of-bounds reads when the NDP32 is placed near the end of the NTB. Add ndpoffset to the nframes bounds check and use struct_size_t() to express the NDP-plus-DPE-array size more clearly. Compile-tested only.

In the Linux kernel, the following vulnerability has been resolved: net: usb: aqc111: Do not perform PM inside suspend callback syzbot reports "task hung in rpm_resume" This is caused by aqc111_suspend calling the PM variant of its write_cmd routine. The simplified call trace looks like this: rpm_suspend() usb_suspend_both() - here udev->dev.power.runtime_status == RPM_SUSPENDING aqc111_suspend() - called for the usb device interface aqc111_write32_cmd() usb_autopm_get_interface() pm_runtime_resume_and_get() rpm_resume() - here we call rpm_resume() on our parent rpm_resume() - Here we wait for a status change that will never happen. At this point we block another task which holds rtnl_lock and locks up the whole networking stack. Fix this by replacing the write_cmd calls with their _nopm variants

In the Linux kernel, the following vulnerability has been resolved: igc: fix page fault in XDP TX timestamps handling If an XDP application that requested TX timestamping is shutting down while the link of the interface in use is still up the following kernel splat is reported: [ 883.803618] [ T1554] BUG: unable to handle page fault for address: ffffcfb6200fd008 ... [ 883.803650] [ T1554] Call Trace: [ 883.803652] [ T1554] <TASK> [ 883.803654] [ T1554] igc_ptp_tx_tstamp_event+0xdf/0x160 [igc] [ 883.803660] [ T1554] igc_tsync_interrupt+0x2d5/0x300 [igc] ... During shutdown of the TX ring the xsk_meta pointers are left behind, so that the IRQ handler is trying to touch them. This issue is now being fixed by cleaning up the stale xsk meta data on TX shutdown. TX timestamps on other queues remain unaffected.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: always free skb on ieee80211_tx_prepare_skb() failure ieee80211_tx_prepare_skb() has three error paths, but only two of them free the skb. The first error path (ieee80211_tx_prepare() returning TX_DROP) does not free it, while invoke_tx_handlers() failure and the fragmentation check both do. Add kfree_skb() to the first error path so all three are consistent, and remove the now-redundant frees in callers (ath9k, mt76, mac80211_hwsim) to avoid double-free. Document the skb ownership guarantee in the function's kdoc.

In the Linux kernel, the following vulnerability has been resolved: ACPI: processor: Fix previous acpi_processor_errata_piix4() fix After commi f132e089fe89 ("ACPI: processor: Fix NULL-pointer dereference in acpi_processor_errata_piix4()"), device pointers may be dereferenced after dropping references to the device objects pointed to by them, which may cause a use-after-free to occur. Moreover, debug messages about enabling the errata may be printed if the errata flags corresponding to them are unset. Address all of these issues by moving message printing to the points in the code where the errata flags are set.

In the Linux kernel, the following vulnerability has been resolved: ipv6: add NULL checks for idev in SRv6 paths __in6_dev_get() can return NULL when the device has no IPv6 configuration (e.g. MTU < IPV6_MIN_MTU or after NETDEV_UNREGISTER). Add NULL checks for idev returned by __in6_dev_get() in both seg6_hmac_validate_skb() and ipv6_srh_rcv() to prevent potential NULL pointer dereferences.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Prevent concurrent access to IPSec ASO context The query or updating IPSec offload object is through Access ASO WQE. The driver uses a single mlx5e_ipsec_aso struct for each PF, which contains a shared DMA-mapped context for all ASO operations. A race condition exists because the ASO spinlock is released before the hardware has finished processing WQE. If a second operation is initiated immediately after, it overwrites the shared context in the DMA area. When the first operation's completion is processed later, it reads this corrupted context, leading to unexpected behavior and incorrect results. This commit fixes the race by introducing a private context within each IPSec offload object. The shared ASO context is now copied to this private context while the ASO spinlock is held. Subsequent processing uses this saved, per-object context, ensuring its integrity is maintained.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix race condition during IPSec ESN update In IPSec full offload mode, the device reports an ESN (Extended Sequence Number) wrap event to the driver. The driver validates this event by querying the IPSec ASO and checking that the esn_event_arm field is 0x0, which indicates an event has occurred. After handling the event, the driver must re-arm the context by setting esn_event_arm back to 0x1. A race condition exists in this handling path. After validating the event, the driver calls mlx5_accel_esp_modify_xfrm() to update the kernel's xfrm state. This function temporarily releases and re-acquires the xfrm state lock. So, need to acknowledge the event first by setting esn_event_arm to 0x1. This prevents the driver from reprocessing the same ESN update if the hardware sends events for other reason. Since the next ESN update only occurs after nearly 2^31 packets are received, there's no risk of missing an update, as it will happen long after this handling has finished. Processing the event twice causes the ESN high-order bits (esn_msb) to be incremented incorrectly. The driver then programs the hardware with this invalid ESN state, which leads to anti-replay failures and a complete halt of IPSec traffic. Fix this by re-arming the ESN event immediately after it is validated, before calling mlx5_accel_esp_modify_xfrm(). This ensures that any spurious, duplicate events are correctly ignored, closing the race window.

In the Linux kernel, the following vulnerability has been resolved: udp_tunnel: fix NULL deref caused by udp_sock_create6 when CONFIG_IPV6=n When CONFIG_IPV6 is disabled, the udp_sock_create6() function returns 0 (success) without actually creating a socket. Callers such as fou_create() then proceed to dereference the uninitialized socket pointer, resulting in a NULL pointer dereference. The captured NULL deref crash: BUG: kernel NULL pointer dereference, address: 0000000000000018 RIP: 0010:fou_nl_add_doit (net/ipv4/fou_core.c:590 net/ipv4/fou_core.c:764) [...] Call Trace: <TASK> genl_family_rcv_msg_doit.constprop.0 (net/netlink/genetlink.c:1114) genl_rcv_msg (net/netlink/genetlink.c:1194 net/netlink/genetlink.c:1209) [...] netlink_rcv_skb (net/netlink/af_netlink.c:2550) genl_rcv (net/netlink/genetlink.c:1219) netlink_unicast (net/netlink/af_netlink.c:1319 net/netlink/af_netlink.c:1344) netlink_sendmsg (net/netlink/af_netlink.c:1894) __sock_sendmsg (net/socket.c:727 (discriminator 1) net/socket.c:742 (discriminator 1)) __sys_sendto (./include/linux/file.h:62 (discriminator 1) ./include/linux/file.h:83 (discriminator 1) net/socket.c:2183 (discriminator 1)) __x64_sys_sendto (net/socket.c:2213 (discriminator 1) net/socket.c:2209 (discriminator 1) net/socket.c:2209 (discriminator 1)) do_syscall_64 (arch/x86/entry/syscall_64.c:63 (discriminator 1) arch/x86/entry/syscall_64.c:94 (discriminator 1)) entry_SYSCALL_64_after_hwframe (net/arch/x86/entry/entry_64.S:130) This patch makes udp_sock_create6 return -EPFNOSUPPORT instead, so callers correctly take their error paths. There is only one caller of the vulnerable function and only privileged users can trigger it.

In the Linux kernel, the following vulnerability has been resolved: net: mvpp2: guard flow control update with global_tx_fc in buffer switching mvpp2_bm_switch_buffers() unconditionally calls mvpp2_bm_pool_update_priv_fc() when switching between per-cpu and shared buffer pool modes. This function programs CM3 flow control registers via mvpp2_cm3_read()/mvpp2_cm3_write(), which dereference priv->cm3_base without any NULL check. When the CM3 SRAM resource is not present in the device tree (the third reg entry added by commit 60523583b07c ("dts: marvell: add CM3 SRAM memory to cp11x ethernet device tree")), priv->cm3_base remains NULL and priv->global_tx_fc is false. Any operation that triggers mvpp2_bm_switch_buffers(), for example an MTU change that crosses the jumbo frame threshold, will crash: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000096000006 EC = 0x25: DABT (current EL), IL = 32 bits pc : readl+0x0/0x18 lr : mvpp2_cm3_read.isra.0+0x14/0x20 Call trace: readl+0x0/0x18 mvpp2_bm_pool_update_fc+0x40/0x12c mvpp2_bm_pool_update_priv_fc+0x94/0xd8 mvpp2_bm_switch_buffers.isra.0+0x80/0x1c0 mvpp2_change_mtu+0x140/0x380 __dev_set_mtu+0x1c/0x38 dev_set_mtu_ext+0x78/0x118 dev_set_mtu+0x48/0xa8 dev_ifsioc+0x21c/0x43c dev_ioctl+0x2d8/0x42c sock_ioctl+0x314/0x378 Every other flow control call site in the driver already guards hardware access with either priv->global_tx_fc or port->tx_fc. mvpp2_bm_switch_buffers() is the only place that omits this check. Add the missing priv->global_tx_fc guard to both the disable and re-enable calls in mvpp2_bm_switch_buffers(), consistent with the rest of the driver.

In the Linux kernel, the following vulnerability has been resolved: net: shaper: protect late read accesses to the hierarchy We look up a netdev during prep of Netlink ops (pre- callbacks) and take a ref to it. Then later in the body of the callback we take its lock or RCU which are the actual protections. This is not proper, a conversion from a ref to a locked netdev must include a liveness check (a check if the netdev hasn't been unregistered already). Fix the read cases (those under RCU). Writes needs a separate change to protect from creating the hierarchy after flush has already run.

In the Linux kernel, the following vulnerability has been resolved: net: shaper: protect from late creation of hierarchy We look up a netdev during prep of Netlink ops (pre- callbacks) and take a ref to it. Then later in the body of the callback we take its lock or RCU which are the actual protections. The netdev may get unregistered in between the time we take the ref and the time we lock it. We may allocate the hierarchy after flush has already run, which would lead to a leak. Take the instance lock in pre- already, this saves us from the race and removes the need for dedicated lock/unlock callbacks completely. After all, if there's any chance of write happening concurrently with the flush - we're back to leaking the hierarchy. We may take the lock for devices which don't support shapers but we're only dealing with SET operations here, not taking the lock would be optimizing for an error case.

In the Linux kernel, the following vulnerability has been resolved: perf/x86: Move event pointer setup earlier in x86_pmu_enable() A production AMD EPYC system crashed with a NULL pointer dereference in the PMU NMI handler: BUG: kernel NULL pointer dereference, address: 0000000000000198 RIP: x86_perf_event_update+0xc/0xa0 Call Trace: <NMI> amd_pmu_v2_handle_irq+0x1a6/0x390 perf_event_nmi_handler+0x24/0x40 The faulting instruction is `cmpq $0x0, 0x198(%rdi)` with RDI=0, corresponding to the `if (unlikely(!hwc->event_base))` check in x86_perf_event_update() where hwc = &event->hw and event is NULL. drgn inspection of the vmcore on CPU 106 showed a mismatch between cpuc->active_mask and cpuc->events[]: active_mask: 0x1e (bits 1, 2, 3, 4) events[1]: 0xff1100136cbd4f38 (valid) events[2]: 0x0 (NULL, but active_mask bit 2 set) events[3]: 0xff1100076fd2cf38 (valid) events[4]: 0xff1100079e990a90 (valid) The event that should occupy events[2] was found in event_list[2] with hw.idx=2 and hw.state=0x0, confirming x86_pmu_start() had run (which clears hw.state and sets active_mask) but events[2] was never populated. Another event (event_list[0]) had hw.state=0x7 (STOPPED|UPTODATE|ARCH), showing it was stopped when the PMU rescheduled events, confirming the throttle-then-reschedule sequence occurred. The root cause is commit 7e772a93eb61 ("perf/x86: Fix NULL event access and potential PEBS record loss") which moved the cpuc->events[idx] assignment out of x86_pmu_start() and into step 2 of x86_pmu_enable(), after the PERF_HES_ARCH check. This broke any path that calls pmu->start() without going through x86_pmu_enable() -- specifically the unthrottle path: perf_adjust_freq_unthr_events() -> perf_event_unthrottle_group() -> perf_event_unthrottle() -> event->pmu->start(event, 0) -> x86_pmu_start() // sets active_mask but not events[] The race sequence is: 1. A group of perf events overflows, triggering group throttle via perf_event_throttle_group(). All events are stopped: active_mask bits cleared, events[] preserved (x86_pmu_stop no longer clears events[] after commit 7e772a93eb61). 2. While still throttled (PERF_HES_STOPPED), x86_pmu_enable() runs due to other scheduling activity. Stopped events that need to move counters get PERF_HES_ARCH set and events[old_idx] cleared. In step 2 of x86_pmu_enable(), PERF_HES_ARCH causes these events to be skipped -- events[new_idx] is never set. 3. The timer tick unthrottles the group via pmu->start(). Since commit 7e772a93eb61 removed the events[] assignment from x86_pmu_start(), active_mask[new_idx] is set but events[new_idx] remains NULL. 4. A PMC overflow NMI fires. The handler iterates active counters, finds active_mask[2] set, reads events[2] which is NULL, and crashes dereferencing it. Move the cpuc->events[hwc->idx] assignment in x86_pmu_enable() to before the PERF_HES_ARCH check, so that events[] is populated even for events that are not immediately started. This ensures the unthrottle path via pmu->start() always finds a valid event pointer.

In the Linux kernel, the following vulnerability has been resolved: mtd: rawnand: serialize lock/unlock against other NAND operations nand_lock() and nand_unlock() call into chip->ops.lock_area/unlock_area without holding the NAND device lock. On controllers that implement SET_FEATURES via multiple low-level PIO commands, these can race with concurrent UBI/UBIFS background erase/write operations that hold the device lock, resulting in cmd_pending conflicts on the NAND controller. Add nand_get_device()/nand_release_device() around the lock/unlock operations to serialize them against all other NAND controller access.

In the Linux kernel, the following vulnerability has been resolved: arm_mpam: Fix null pointer dereference when restoring bandwidth counters When an MSC supporting memory bandwidth monitoring is brought offline and then online, mpam_restore_mbwu_state() calls __ris_msmon_read() via ipi to restore the configuration of the bandwidth counters. It doesn't care about the value read, mbwu_arg.val, and doesn't set it leading to a null pointer dereference when __ris_msmon_read() adds to it. This results in a kernel oops with a call trace such as: Call trace: __ris_msmon_read+0x19c/0x64c (P) mpam_restore_mbwu_state+0xa0/0xe8 smp_call_on_cpu_callback+0x1c/0x38 process_one_work+0x154/0x4b4 worker_thread+0x188/0x310 kthread+0x11c/0x130 ret_from_fork+0x10/0x20 Provide a local variable for val to avoid __ris_msmon_read() dereferencing a null pointer when adding to val.

In the Linux kernel, the following vulnerability has been resolved: mshv: Fix use-after-free in mshv_map_user_memory error path In the error path of mshv_map_user_memory(), calling vfree() directly on the region leaves the MMU notifier registered. When userspace later unmaps the memory, the notifier fires and accesses the freed region, causing a use-after-free and potential kernel panic. Replace vfree() with mshv_partition_put() to properly unregister the MMU notifier before freeing the region.

In the Linux kernel, the following vulnerability has been resolved: spi: amlogic-spisg: Fix memory leak in aml_spisg_probe() In aml_spisg_probe(), ctlr is allocated by spi_alloc_target()/spi_alloc_host(), but fails to call spi_controller_put() in several error paths. This leads to a memory leak whenever the driver fails to probe after the initial allocation. Convert to use devm_spi_alloc_host()/devm_spi_alloc_target() to fix the memory leak.

In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Don't overwrite KMS surface dirty tracker We were overwriting the surface's dirty tracker here causing a memory leak.

In the Linux kernel, the following vulnerability has been resolved: iommu/sva: Fix crash in iommu_sva_unbind_device() domain->mm->iommu_mm can be freed by iommu_domain_free(): iommu_domain_free() mmdrop() __mmdrop() mm_pasid_drop() After iommu_domain_free() returns, accessing domain->mm->iommu_mm may dereference a freed mm structure, leading to a crash. Fix this by moving the code that accesses domain->mm->iommu_mm to before the call to iommu_domain_free().

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix use-after-free of share_conf in compound request smb2_get_ksmbd_tcon() reuses work->tcon in compound requests without validating tcon->t_state. ksmbd_tree_conn_lookup() checks t_state == TREE_CONNECTED on the initial lookup path, but the compound reuse path bypasses this check entirely. If a prior command in the compound (SMB2_TREE_DISCONNECT) sets t_state to TREE_DISCONNECTED and frees share_conf via ksmbd_share_config_put(), subsequent commands dereference the freed share_conf through work->tcon->share_conf. KASAN report: [ 4.144653] ================================================================== [ 4.145059] BUG: KASAN: slab-use-after-free in smb2_write+0xc74/0xe70 [ 4.145415] Read of size 4 at addr ffff88810430c194 by task kworker/1:1/44 [ 4.145772] [ 4.145867] CPU: 1 UID: 0 PID: 44 Comm: kworker/1:1 Not tainted 7.0.0-rc3+ #60 PREEMPTLAZY [ 4.145871] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 4.145875] Workqueue: ksmbd-io handle_ksmbd_work [ 4.145888] Call Trace: [ 4.145892] <TASK> [ 4.145894] dump_stack_lvl+0x64/0x80 [ 4.145910] print_report+0xce/0x660 [ 4.145919] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 4.145928] ? smb2_write+0xc74/0xe70 [ 4.145931] kasan_report+0xce/0x100 [ 4.145934] ? smb2_write+0xc74/0xe70 [ 4.145937] smb2_write+0xc74/0xe70 [ 4.145939] ? __pfx_smb2_write+0x10/0x10 [ 4.145942] ? _raw_spin_unlock+0xe/0x30 [ 4.145945] ? ksmbd_smb2_check_message+0xeb2/0x24c0 [ 4.145948] ? smb2_tree_disconnect+0x31c/0x480 [ 4.145951] handle_ksmbd_work+0x40f/0x1080 [ 4.145953] process_one_work+0x5fa/0xef0 [ 4.145962] ? assign_work+0x122/0x3e0 [ 4.145964] worker_thread+0x54b/0xf70 [ 4.145967] ? __pfx_worker_thread+0x10/0x10 [ 4.145970] kthread+0x346/0x470 [ 4.145976] ? recalc_sigpending+0x19b/0x230 [ 4.145980] ? __pfx_kthread+0x10/0x10 [ 4.145984] ret_from_fork+0x4fb/0x6c0 [ 4.145992] ? __pfx_ret_from_fork+0x10/0x10 [ 4.145995] ? __switch_to+0x36c/0xbe0 [ 4.145999] ? __pfx_kthread+0x10/0x10 [ 4.146003] ret_from_fork_asm+0x1a/0x30 [ 4.146013] </TASK> [ 4.146014] [ 4.149858] Allocated by task 44: [ 4.149953] kasan_save_stack+0x33/0x60 [ 4.150061] kasan_save_track+0x14/0x30 [ 4.150169] __kasan_kmalloc+0x8f/0xa0 [ 4.150274] ksmbd_share_config_get+0x1dd/0xdd0 [ 4.150401] ksmbd_tree_conn_connect+0x7e/0x600 [ 4.150529] smb2_tree_connect+0x2e6/0x1000 [ 4.150645] handle_ksmbd_work+0x40f/0x1080 [ 4.150761] process_one_work+0x5fa/0xef0 [ 4.150873] worker_thread+0x54b/0xf70 [ 4.150978] kthread+0x346/0x470 [ 4.151071] ret_from_fork+0x4fb/0x6c0 [ 4.151176] ret_from_fork_asm+0x1a/0x30 [ 4.151286] [ 4.151332] Freed by task 44: [ 4.151418] kasan_save_stack+0x33/0x60 [ 4.151526] kasan_save_track+0x14/0x30 [ 4.151634] kasan_save_free_info+0x3b/0x60 [ 4.151751] __kasan_slab_free+0x43/0x70 [ 4.151861] kfree+0x1ca/0x430 [ 4.151952] __ksmbd_tree_conn_disconnect+0xc8/0x190 [ 4.152088] smb2_tree_disconnect+0x1cd/0x480 [ 4.152211] handle_ksmbd_work+0x40f/0x1080 [ 4.152326] process_one_work+0x5fa/0xef0 [ 4.152438] worker_thread+0x54b/0xf70 [ 4.152545] kthread+0x346/0x470 [ 4.152638] ret_from_fork+0x4fb/0x6c0 [ 4.152743] ret_from_fork_asm+0x1a/0x30 [ 4.152853] [ 4.152900] The buggy address belongs to the object at ffff88810430c180 [ 4.152900] which belongs to the cache kmalloc-96 of size 96 [ 4.153226] The buggy address is located 20 bytes inside of [ 4.153226] freed 96-byte region [ffff88810430c180, ffff88810430c1e0) [ 4.153549] [ 4.153596] The buggy address belongs to the physical page: [ 4.153750] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0xffff88810430ce80 pfn:0x10430c [ 4.154000] flags: 0x ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix use-after-free in durable v2 replay of active file handles parse_durable_handle_context() unconditionally assigns dh_info->fp->conn to the current connection when handling a DURABLE_REQ_V2 context with SMB2_FLAGS_REPLAY_OPERATION. ksmbd_lookup_fd_cguid() does not filter by fp->conn, so it returns file handles that are already actively connected. The unconditional overwrite replaces fp->conn, and when the overwriting connection is subsequently freed, __ksmbd_close_fd() dereferences the stale fp->conn via spin_lock(&fp->conn->llist_lock), causing a use-after-free. KASAN report: [ 7.349357] ================================================================== [ 7.349607] BUG: KASAN: slab-use-after-free in _raw_spin_lock+0x75/0xe0 [ 7.349811] Write of size 4 at addr ffff8881056ac18c by task kworker/1:2/108 [ 7.350010] [ 7.350064] CPU: 1 UID: 0 PID: 108 Comm: kworker/1:2 Not tainted 7.0.0-rc3+ #58 PREEMPTLAZY [ 7.350068] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 7.350070] Workqueue: ksmbd-io handle_ksmbd_work [ 7.350083] Call Trace: [ 7.350087] <TASK> [ 7.350087] dump_stack_lvl+0x64/0x80 [ 7.350094] print_report+0xce/0x660 [ 7.350100] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 7.350101] ? __pfx___mod_timer+0x10/0x10 [ 7.350106] ? _raw_spin_lock+0x75/0xe0 [ 7.350108] kasan_report+0xce/0x100 [ 7.350109] ? _raw_spin_lock+0x75/0xe0 [ 7.350114] kasan_check_range+0x105/0x1b0 [ 7.350116] _raw_spin_lock+0x75/0xe0 [ 7.350118] ? __pfx__raw_spin_lock+0x10/0x10 [ 7.350119] ? __call_rcu_common.constprop.0+0x25e/0x780 [ 7.350125] ? close_id_del_oplock+0x2cc/0x4e0 [ 7.350128] __ksmbd_close_fd+0x27f/0xaf0 [ 7.350131] ksmbd_close_fd+0x135/0x1b0 [ 7.350133] smb2_close+0xb19/0x15b0 [ 7.350142] ? __pfx_smb2_close+0x10/0x10 [ 7.350143] ? xas_load+0x18/0x270 [ 7.350146] ? _raw_spin_lock+0x84/0xe0 [ 7.350148] ? __pfx__raw_spin_lock+0x10/0x10 [ 7.350150] ? _raw_spin_unlock+0xe/0x30 [ 7.350151] ? ksmbd_smb2_check_message+0xeb2/0x24c0 [ 7.350153] ? ksmbd_tree_conn_lookup+0xcd/0xf0 [ 7.350154] handle_ksmbd_work+0x40f/0x1080 [ 7.350156] process_one_work+0x5fa/0xef0 [ 7.350162] ? assign_work+0x122/0x3e0 [ 7.350163] worker_thread+0x54b/0xf70 [ 7.350165] ? __pfx_worker_thread+0x10/0x10 [ 7.350166] kthread+0x346/0x470 [ 7.350170] ? recalc_sigpending+0x19b/0x230 [ 7.350176] ? __pfx_kthread+0x10/0x10 [ 7.350178] ret_from_fork+0x4fb/0x6c0 [ 7.350183] ? __pfx_ret_from_fork+0x10/0x10 [ 7.350185] ? __switch_to+0x36c/0xbe0 [ 7.350188] ? __pfx_kthread+0x10/0x10 [ 7.350190] ret_from_fork_asm+0x1a/0x30 [ 7.350197] </TASK> [ 7.350197] [ 7.355160] Allocated by task 123: [ 7.355261] kasan_save_stack+0x33/0x60 [ 7.355373] kasan_save_track+0x14/0x30 [ 7.355484] __kasan_kmalloc+0x8f/0xa0 [ 7.355593] ksmbd_conn_alloc+0x44/0x6d0 [ 7.355711] ksmbd_kthread_fn+0x243/0xd70 [ 7.355839] kthread+0x346/0x470 [ 7.355942] ret_from_fork+0x4fb/0x6c0 [ 7.356051] ret_from_fork_asm+0x1a/0x30 [ 7.356164] [ 7.356214] Freed by task 134: [ 7.356305] kasan_save_stack+0x33/0x60 [ 7.356416] kasan_save_track+0x14/0x30 [ 7.356527] kasan_save_free_info+0x3b/0x60 [ 7.356646] __kasan_slab_free+0x43/0x70 [ 7.356761] kfree+0x1ca/0x430 [ 7.356862] ksmbd_tcp_disconnect+0x59/0xe0 [ 7.356993] ksmbd_conn_handler_loop+0x77e/0xd40 [ 7.357138] kthread+0x346/0x470 [ 7.357240] ret_from_fork+0x4fb/0x6c0 [ 7.357350] ret_from_fork_asm+0x1a/0x30 [ 7.357463] [ 7.357513] The buggy address belongs to the object at ffff8881056ac000 [ 7.357513] which belongs to the cache kmalloc-1k of size 1024 [ 7.357857] The buggy address is located 396 bytes inside of [ 7.357857] freed 1024-byte region ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/logicvc: Fix device node reference leak in logicvc_drm_config_parse() The logicvc_drm_config_parse() function calls of_get_child_by_name() to find the "layers" node but fails to release the reference, leading to a device node reference leak. Fix this by using the __free(device_node) cleanup attribute to automatic release the reference when the variable goes out of scope.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Fix ID register initialization for non-protected pKVM guests In protected mode, the hypervisor maintains a separate instance of the `kvm` structure for each VM. For non-protected VMs, this structure is initialized from the host's `kvm` state. Currently, `pkvm_init_features_from_host()` copies the `KVM_ARCH_FLAG_ID_REGS_INITIALIZED` flag from the host without the underlying `id_regs` data being initialized. This results in the hypervisor seeing the flag as set while the ID registers remain zeroed. Consequently, `kvm_has_feat()` checks at EL2 fail (return 0) for non-protected VMs. This breaks logic that relies on feature detection, such as `ctxt_has_tcrx()` for TCR2_EL1 support. As a result, certain system registers (e.g., TCR2_EL1, PIR_EL1, POR_EL1) are not saved/restored during the world switch, which could lead to state corruption. Fix this by explicitly copying the ID registers from the host `kvm` to the hypervisor `kvm` for non-protected VMs during initialization, since we trust the host with its non-protected guests' features. Also ensure `KVM_ARCH_FLAG_ID_REGS_INITIALIZED` is cleared initially in `pkvm_init_features_from_host` so that `vm_copy_id_regs` can properly initialize them and set the flag once done.

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Validate command buffer payload count The count field in the command header is used to determine the valid payload size. Verify that the valid payload does not exceed the remaining buffer space.

In the Linux kernel, the following vulnerability has been resolved: btrfs: free pages on error in btrfs_uring_read_extent() In this function the 'pages' object is never freed in the hopes that it is picked up by btrfs_uring_read_finished() whenever that executes in the future. But that's just the happy path. Along the way previous allocations might have gone wrong, or we might not get -EIOCBQUEUED from btrfs_encoded_read_regular_fill_pages(). In all these cases, we go to a cleanup section that frees all memory allocated by this function without assuming any deferred execution, and this also needs to happen for the 'pages' allocation.

In the Linux kernel, the following vulnerability has been resolved: xdp: produce a warning when calculated tailroom is negative Many ethernet drivers report xdp Rx queue frag size as being the same as DMA write size. However, the only user of this field, namely bpf_xdp_frags_increase_tail(), clearly expects a truesize. Such difference leads to unspecific memory corruption issues under certain circumstances, e.g. in ixgbevf maximum DMA write size is 3 KB, so when running xskxceiver's XDP_ADJUST_TAIL_GROW_MULTI_BUFF, 6K packet fully uses all DMA-writable space in 2 buffers. This would be fine, if only rxq->frag_size was properly set to 4K, but value of 3K results in a negative tailroom, because there is a non-zero page offset. We are supposed to return -EINVAL and be done with it in such case, but due to tailroom being stored as an unsigned int, it is reported to be somewhere near UINT_MAX, resulting in a tail being grown, even if the requested offset is too much (it is around 2K in the abovementioned test). This later leads to all kinds of unspecific calltraces. [ 7340.337579] xskxceiver[1440]: segfault at 1da718 ip 00007f4161aeac9d sp 00007f41615a6a00 error 6 [ 7340.338040] xskxceiver[1441]: segfault at 7f410000000b ip 00000000004042b5 sp 00007f415bffecf0 error 4 [ 7340.338179] in libc.so.6[61c9d,7f4161aaf000+160000] [ 7340.339230] in xskxceiver[42b5,400000+69000] [ 7340.340300] likely on CPU 6 (core 0, socket 6) [ 7340.340302] Code: ff ff 01 e9 f4 fe ff ff 0f 1f 44 00 00 4c 39 f0 74 73 31 c0 ba 01 00 00 00 f0 0f b1 17 0f 85 ba 00 00 00 49 8b 87 88 00 00 00 <4c> 89 70 08 eb cc 0f 1f 44 00 00 48 8d bd f0 fe ff ff 89 85 ec fe [ 7340.340888] likely on CPU 3 (core 0, socket 3) [ 7340.345088] Code: 00 00 00 ba 00 00 00 00 be 00 00 00 00 89 c7 e8 31 ca ff ff 89 45 ec 8b 45 ec 85 c0 78 07 b8 00 00 00 00 eb 46 e8 0b c8 ff ff <8b> 00 83 f8 69 74 24 e8 ff c7 ff ff 8b 00 83 f8 0b 74 18 e8 f3 c7 [ 7340.404334] Oops: general protection fault, probably for non-canonical address 0x6d255010bdffc: 0000 [#1] SMP NOPTI [ 7340.405972] CPU: 7 UID: 0 PID: 1439 Comm: xskxceiver Not tainted 6.19.0-rc1+ #21 PREEMPT(lazy) [ 7340.408006] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-5.fc42 04/01/2014 [ 7340.409716] RIP: 0010:lookup_swap_cgroup_id+0x44/0x80 [ 7340.410455] Code: 83 f8 1c 73 39 48 ba ff ff ff ff ff ff ff 03 48 8b 04 c5 20 55 fa bd 48 21 d1 48 89 ca 83 e1 01 48 d1 ea c1 e1 04 48 8d 04 90 <8b> 00 48 83 c4 10 d3 e8 c3 cc cc cc cc 31 c0 e9 98 b7 dd 00 48 89 [ 7340.412787] RSP: 0018:ffffcc5c04f7f6d0 EFLAGS: 00010202 [ 7340.413494] RAX: 0006d255010bdffc RBX: ffff891f477895a8 RCX: 0000000000000010 [ 7340.414431] RDX: 0001c17e3fffffff RSI: 00fa070000000000 RDI: 000382fc7fffffff [ 7340.415354] RBP: 00fa070000000000 R08: ffffcc5c04f7f8f8 R09: ffffcc5c04f7f7d0 [ 7340.416283] R10: ffff891f4c1a7000 R11: ffffcc5c04f7f9c8 R12: ffffcc5c04f7f7d0 [ 7340.417218] R13: 03ffffffffffffff R14: 00fa06fffffffe00 R15: ffff891f47789500 [ 7340.418229] FS: 0000000000000000(0000) GS:ffff891ffdfaa000(0000) knlGS:0000000000000000 [ 7340.419489] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 7340.420286] CR2: 00007f415bfffd58 CR3: 0000000103f03002 CR4: 0000000000772ef0 [ 7340.421237] PKRU: 55555554 [ 7340.421623] Call Trace: [ 7340.421987] <TASK> [ 7340.422309] ? softleaf_from_pte+0x77/0xa0 [ 7340.422855] swap_pte_batch+0xa7/0x290 [ 7340.423363] zap_nonpresent_ptes.constprop.0.isra.0+0xd1/0x270 [ 7340.424102] zap_pte_range+0x281/0x580 [ 7340.424607] zap_pmd_range.isra.0+0xc9/0x240 [ 7340.425177] unmap_page_range+0x24d/0x420 [ 7340.425714] unmap_vmas+0xa1/0x180 [ 7340.426185] exit_mmap+0xe1/0x3b0 [ 7340.426644] __mmput+0x41/0x150 [ 7340.427098] exit_mm+0xb1/0x110 [ 7340.427539] do_exit+0x1b2/0x460 [ 7340.427992] do_group_exit+0x2d/0xc0 [ 7340.428477] get_signal+0x79d/0x7e0 [ 7340.428957] arch_do_signal_or_restart+0x34/0x100 [ 7340.429571] exit_to_user_mode_loop+0x8e/0x4c0 [ 7340.430159] do_syscall_64+0x188/ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix race in cpumap on PREEMPT_RT On PREEMPT_RT kernels, the per-CPU xdp_bulk_queue (bq) can be accessed concurrently by multiple preemptible tasks on the same CPU. The original code assumes bq_enqueue() and __cpu_map_flush() run atomically with respect to each other on the same CPU, relying on local_bh_disable() to prevent preemption. However, on PREEMPT_RT, local_bh_disable() only calls migrate_disable() (when PREEMPT_RT_NEEDS_BH_LOCK is not set) and does not disable preemption, which allows CFS scheduling to preempt a task during bq_flush_to_queue(), enabling another task on the same CPU to enter bq_enqueue() and operate on the same per-CPU bq concurrently. This leads to several races: 1. Double __list_del_clearprev(): after bq->count is reset in bq_flush_to_queue(), a preempting task can call bq_enqueue() -> bq_flush_to_queue() on the same bq when bq->count reaches CPU_MAP_BULK_SIZE. Both tasks then call __list_del_clearprev() on the same bq->flush_node, the second call dereferences the prev pointer that was already set to NULL by the first. 2. bq->count and bq->q[] races: concurrent bq_enqueue() can corrupt the packet queue while bq_flush_to_queue() is processing it. The race between task A (__cpu_map_flush -> bq_flush_to_queue) and task B (bq_enqueue -> bq_flush_to_queue) on the same CPU: Task A (xdp_do_flush) Task B (cpu_map_enqueue) ---------------------- ------------------------ bq_flush_to_queue(bq) spin_lock(&q->producer_lock) /* flush bq->q[] to ptr_ring */ bq->count = 0 spin_unlock(&q->producer_lock) bq_enqueue(rcpu, xdpf) <-- CFS preempts Task A --> bq->q[bq->count++] = xdpf /* ... more enqueues until full ... */ bq_flush_to_queue(bq) spin_lock(&q->producer_lock) /* flush to ptr_ring */ spin_unlock(&q->producer_lock) __list_del_clearprev(flush_node) /* sets flush_node.prev = NULL */ <-- Task A resumes --> __list_del_clearprev(flush_node) flush_node.prev->next = ... /* prev is NULL -> kernel oops */ Fix this by adding a local_lock_t to xdp_bulk_queue and acquiring it in bq_enqueue() and __cpu_map_flush(). These paths already run under local_bh_disable(), so use local_lock_nested_bh() which on non-RT is a pure annotation with no overhead, and on PREEMPT_RT provides a per-CPU sleeping lock that serializes access to the bq. To reproduce, insert an mdelay(100) between bq->count = 0 and __list_del_clearprev() in bq_flush_to_queue(), then run reproducer provided by syzkaller.

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Fix crash when destroying a suspended hardware context If userspace issues an ioctl to destroy a hardware context that has already been automatically suspended, the driver may crash because the mailbox channel pointer is NULL for the suspended context. Fix this by checking the mailbox channel pointer in aie2_destroy_context() before accessing it.

In the Linux kernel, the following vulnerability has been resolved: net: sched: avoid qdisc_reset_all_tx_gt() vs dequeue race for lockless qdiscs When shrinking the number of real tx queues, netif_set_real_num_tx_queues() calls qdisc_reset_all_tx_gt() to flush qdiscs for queues which will no longer be used. qdisc_reset_all_tx_gt() currently serializes qdisc_reset() with qdisc_lock(). However, for lockless qdiscs, the dequeue path is serialized by qdisc_run_begin/end() using qdisc->seqlock instead, so qdisc_reset() can run concurrently with __qdisc_run() and free skbs while they are still being dequeued, leading to UAF. This can easily be reproduced on e.g. virtio-net by imposing heavy traffic while frequently changing the number of queue pairs: iperf3 -ub0 -c $peer -t 0 & while :; do ethtool -L eth0 combined 1 ethtool -L eth0 combined 2 done With KASAN enabled, this leads to reports like: BUG: KASAN: slab-use-after-free in __qdisc_run+0x133f/0x1760 ... Call Trace: <TASK> ... __qdisc_run+0x133f/0x1760 __dev_queue_xmit+0x248f/0x3550 ip_finish_output2+0xa42/0x2110 ip_output+0x1a7/0x410 ip_send_skb+0x2e6/0x480 udp_send_skb+0xb0a/0x1590 udp_sendmsg+0x13c9/0x1fc0 ... </TASK> Allocated by task 1270 on cpu 5 at 44.558414s: ... alloc_skb_with_frags+0x84/0x7c0 sock_alloc_send_pskb+0x69a/0x830 __ip_append_data+0x1b86/0x48c0 ip_make_skb+0x1e8/0x2b0 udp_sendmsg+0x13a6/0x1fc0 ... Freed by task 1306 on cpu 3 at 44.558445s: ... kmem_cache_free+0x117/0x5e0 pfifo_fast_reset+0x14d/0x580 qdisc_reset+0x9e/0x5f0 netif_set_real_num_tx_queues+0x303/0x840 virtnet_set_channels+0x1bf/0x260 [virtio_net] ethnl_set_channels+0x684/0xae0 ethnl_default_set_doit+0x31a/0x890 ... Serialize qdisc_reset_all_tx_gt() against the lockless dequeue path by taking qdisc->seqlock for TCQ_F_NOLOCK qdiscs, matching the serialization model already used by dev_reset_queue(). Additionally clear QDISC_STATE_NON_EMPTY after reset so the qdisc state reflects an empty queue, avoiding needless re-scheduling.

In the Linux kernel, the following vulnerability has been resolved: nfc: nci: free skb on nci_transceive early error paths nci_transceive() takes ownership of the skb passed by the caller, but the -EPROTO, -EINVAL, and -EBUSY error paths return without freeing it. Due to issues clearing NCI_DATA_EXCHANGE fixed by subsequent changes the nci/nci_dev selftest hits the error path occasionally in NIPA, and kmemleak detects leaks: unreferenced object 0xff11000015ce6a40 (size 640): comm "nci_dev", pid 3954, jiffies 4295441246 hex dump (first 32 bytes): 6b 6b 6b 6b 00 a4 00 0c 02 e1 03 6b 6b 6b 6b 6b kkkk.......kkkkk 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk backtrace (crc 7c40cc2a): kmem_cache_alloc_node_noprof+0x492/0x630 __alloc_skb+0x11e/0x5f0 alloc_skb_with_frags+0xc6/0x8f0 sock_alloc_send_pskb+0x326/0x3f0 nfc_alloc_send_skb+0x94/0x1d0 rawsock_sendmsg+0x162/0x4c0 do_syscall_64+0x117/0xfc0

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/userq: Do not allow userspace to trivially triger kernel warnings Userspace can either deliberately pass in the too small num_fences, or the required number can legitimately grow between the two calls to the userq wait ioctl. In both cases we do not want the emit the kernel warning backtrace since nothing is wrong with the kernel and userspace will simply get an errno reported back. So lets simply drop the WARN_ONs. (cherry picked from commit 2c333ea579de6cc20ea7bc50e9595ef72863e65c)

In the Linux kernel, the following vulnerability has been resolved: pinctrl: pinconf-generic: Fix memory leak in pinconf_generic_parse_dt_config() In pinconf_generic_parse_dt_config(), if parse_dt_cfg() fails, it returns directly. This bypasses the cleanup logic and results in a memory leak of the cfg buffer. Fix this by jumping to the out label on failure, ensuring kfree(cfg) is called before returning.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: cancel rfkill_block work in wiphy_unregister() There is a use-after-free error in cfg80211_shutdown_all_interfaces found by syzkaller: BUG: KASAN: use-after-free in cfg80211_shutdown_all_interfaces+0x213/0x220 Read of size 8 at addr ffff888112a78d98 by task kworker/0:5/5326 CPU: 0 UID: 0 PID: 5326 Comm: kworker/0:5 Not tainted 6.19.0-rc2 #2 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Workqueue: events cfg80211_rfkill_block_work Call Trace: <TASK> dump_stack_lvl+0x116/0x1f0 print_report+0xcd/0x630 kasan_report+0xe0/0x110 cfg80211_shutdown_all_interfaces+0x213/0x220 cfg80211_rfkill_block_work+0x1e/0x30 process_one_work+0x9cf/0x1b70 worker_thread+0x6c8/0xf10 kthread+0x3c5/0x780 ret_from_fork+0x56d/0x700 ret_from_fork_asm+0x1a/0x30 </TASK> The problem arises due to the rfkill_block work is not cancelled when wiphy is being unregistered. In order to fix the issue cancel the corresponding work in wiphy_unregister(). Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: RDMA/irdma: Fix kernel stack leak in irdma_create_user_ah() struct irdma_create_ah_resp { // 8 bytes, no padding __u32 ah_id; // offset 0 - SET (uresp.ah_id = ah->sc_ah.ah_info.ah_idx) __u8 rsvd[4]; // offset 4 - NEVER SET <- LEAK }; rsvd[4]: 4 bytes of stack memory leaked unconditionally. Only ah_id is assigned before ib_respond_udata(). The reserved members of the structure were not zeroed.

In the Linux kernel, the following vulnerability has been resolved: can: usb: f81604: handle short interrupt urb messages properly If an interrupt urb is received that is not the correct length, properly detect it and don't attempt to treat the data as valid.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: intel_pstate: Fix crash during turbo disable When the system is booted with kernel command line argument "nosmt" or "maxcpus" to limit the number of CPUs, disabling turbo via: echo 1 > /sys/devices/system/cpu/intel_pstate/no_turbo results in a crash: PF: supervisor read access in kernel mode PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP PTI ... RIP: 0010:store_no_turbo+0x100/0x1f0 ... This occurs because for_each_possible_cpu() returns CPUs even if they are not online. For those CPUs, all_cpu_data[] will be NULL. Since commit 973207ae3d7c ("cpufreq: intel_pstate: Rearrange max frequency updates handling code"), all_cpu_data[] is dereferenced even for CPUs which are not online, causing the NULL pointer dereference. To fix that, pass CPU number to intel_pstate_update_max_freq() and use all_cpu_data[] for those CPUs for which there is a valid cpufreq policy.

In the Linux kernel, the following vulnerability has been resolved: udp: Unhash auto-bound connected sk from 4-tuple hash table when disconnected. Let's say we bind() an UDP socket to the wildcard address with a non-zero port, connect() it to an address, and disconnect it from the address. bind() sets SOCK_BINDPORT_LOCK on sk->sk_userlocks (but not SOCK_BINDADDR_LOCK), and connect() calls udp_lib_hash4() to put the socket into the 4-tuple hash table. Then, __udp_disconnect() calls sk->sk_prot->rehash(sk). It computes a new hash based on the wildcard address and moves the socket to a new slot in the 4-tuple hash table, leaving a garbage in the chain that no packet hits. Let's remove such a socket from 4-tuple hash table when disconnected. Note that udp_sk(sk)->udp_portaddr_hash needs to be udpated after udp_hash4_dec(hslot2) in udp_unhash4().

In the Linux kernel, the following vulnerability has been resolved: nfc: nci: complete pending data exchange on device close In nci_close_device(), complete any pending data exchange before closing. The data exchange callback (e.g. rawsock_data_exchange_complete) holds a socket reference. NIPA occasionally hits this leak: unreferenced object 0xff1100000f435000 (size 2048): comm "nci_dev", pid 3954, jiffies 4295441245 hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 27 00 01 40 00 00 00 00 00 00 00 00 00 00 00 00 '..@............ backtrace (crc ec2b3c5): __kmalloc_noprof+0x4db/0x730 sk_prot_alloc.isra.0+0xe4/0x1d0 sk_alloc+0x36/0x760 rawsock_create+0xd1/0x540 nfc_sock_create+0x11f/0x280 __sock_create+0x22d/0x630 __sys_socket+0x115/0x1d0 __x64_sys_socket+0x72/0xd0 do_syscall_64+0x117/0xfc0 entry_SYSCALL_64_after_hwframe+0x4b/0x53

In the Linux kernel, the following vulnerability has been resolved: libie: don't unroll if fwlog isn't supported The libie_fwlog_deinit() function can be called during driver unload even when firmware logging was never properly initialized. This led to call trace: [ 148.576156] Oops: Oops: 0000 [#1] SMP NOPTI [ 148.576167] CPU: 80 UID: 0 PID: 12843 Comm: rmmod Kdump: loaded Not tainted 6.17.0-rc7next-queue-3oct-01915-g06d79d51cf51 #1 PREEMPT(full) [ 148.576177] Hardware name: HPE ProLiant DL385 Gen10 Plus/ProLiant DL385 Gen10 Plus, BIOS A42 07/18/2020 [ 148.576182] RIP: 0010:__dev_printk+0x16/0x70 [ 148.576196] Code: 1f 44 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 41 55 41 54 49 89 d4 55 48 89 fd 53 48 85 f6 74 3c <4c> 8b 6e 50 48 89 f3 4d 85 ed 75 03 4c 8b 2e 48 89 df e8 f3 27 98 [ 148.576204] RSP: 0018:ffffd2fd7ea17a48 EFLAGS: 00010202 [ 148.576211] RAX: ffffd2fd7ea17aa0 RBX: ffff8eb288ae2000 RCX: 0000000000000000 [ 148.576217] RDX: ffffd2fd7ea17a70 RSI: 00000000000000c8 RDI: ffffffffb68d3d88 [ 148.576222] RBP: ffffffffb68d3d88 R08: 0000000000000000 R09: 0000000000000000 [ 148.576227] R10: 00000000000000c8 R11: ffff8eb2b1a49400 R12: ffffd2fd7ea17a70 [ 148.576231] R13: ffff8eb3141fb000 R14: ffffffffc1215b48 R15: ffffffffc1215bd8 [ 148.576236] FS: 00007f5666ba6740(0000) GS:ffff8eb2472b9000(0000) knlGS:0000000000000000 [ 148.576242] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 148.576247] CR2: 0000000000000118 CR3: 000000011ad17000 CR4: 0000000000350ef0 [ 148.576252] Call Trace: [ 148.576258] <TASK> [ 148.576269] _dev_warn+0x7c/0x96 [ 148.576290] libie_fwlog_deinit+0x112/0x117 [libie_fwlog] [ 148.576303] ixgbe_remove+0x63/0x290 [ixgbe] [ 148.576342] pci_device_remove+0x42/0xb0 [ 148.576354] device_release_driver_internal+0x19c/0x200 [ 148.576365] driver_detach+0x48/0x90 [ 148.576372] bus_remove_driver+0x6d/0xf0 [ 148.576383] pci_unregister_driver+0x2e/0xb0 [ 148.576393] ixgbe_exit_module+0x1c/0xd50 [ixgbe] [ 148.576430] __do_sys_delete_module.isra.0+0x1bc/0x2e0 [ 148.576446] do_syscall_64+0x7f/0x980 It can be reproduced by trying to unload ixgbe driver in recovery mode. Fix that by checking if fwlog is supported before doing unroll.

In the Linux kernel, the following vulnerability has been resolved: accel/amdxdna: Fix NULL pointer dereference of mgmt_chann mgmt_chann may be set to NULL if the firmware returns an unexpected error in aie2_send_mgmt_msg_wait(). This can later lead to a NULL pointer dereference in aie2_hw_stop(). Fix this by introducing a dedicated helper to destroy mgmt_chann and by adding proper NULL checks before accessing it.

In the Linux kernel, the following vulnerability has been resolved: cxl/mbox: validate payload size before accessing contents in cxl_payload_from_user_allowed() cxl_payload_from_user_allowed() casts and dereferences the input payload without first verifying its size. When a raw mailbox command is sent with an undersized payload (ie: 1 byte for CXL_MBOX_OP_CLEAR_LOG, which expects a 16-byte UUID), uuid_equal() reads past the allocated buffer, triggering a KASAN splat: BUG: KASAN: slab-out-of-bounds in memcmp+0x176/0x1d0 lib/string.c:683 Read of size 8 at addr ffff88810130f5c0 by task syz.1.62/2258 CPU: 2 UID: 0 PID: 2258 Comm: syz.1.62 Not tainted 6.19.0-dirty #3 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0xab/0xe0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xce/0x650 mm/kasan/report.c:482 kasan_report+0xce/0x100 mm/kasan/report.c:595 memcmp+0x176/0x1d0 lib/string.c:683 uuid_equal include/linux/uuid.h:73 [inline] cxl_payload_from_user_allowed drivers/cxl/core/mbox.c:345 [inline] cxl_mbox_cmd_ctor drivers/cxl/core/mbox.c:368 [inline] cxl_validate_cmd_from_user drivers/cxl/core/mbox.c:522 [inline] cxl_send_cmd+0x9c0/0xb50 drivers/cxl/core/mbox.c:643 __cxl_memdev_ioctl drivers/cxl/core/memdev.c:698 [inline] cxl_memdev_ioctl+0x14f/0x190 drivers/cxl/core/memdev.c:713 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:597 [inline] __se_sys_ioctl fs/ioctl.c:583 [inline] __x64_sys_ioctl+0x18e/0x210 fs/ioctl.c:583 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xa8/0x330 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7fdaf331ba79 Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fdaf1d77038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007fdaf3585fa0 RCX: 00007fdaf331ba79 RDX: 00002000000001c0 RSI: 00000000c030ce02 RDI: 0000000000000003 RBP: 00007fdaf33749df R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007fdaf3586038 R14: 00007fdaf3585fa0 R15: 00007ffced2af768 </TASK> Add 'in_size' parameter to cxl_payload_from_user_allowed() and validate the payload is large enough.

In the Linux kernel, the following vulnerability has been resolved: xsk: Fix fragment node deletion to prevent buffer leak After commit b692bf9a7543 ("xsk: Get rid of xdp_buff_xsk::xskb_list_node"), the list_node field is reused for both the xskb pool list and the buffer free list, this causes a buffer leak as described below. xp_free() checks if a buffer is already on the free list using list_empty(&xskb->list_node). When list_del() is used to remove a node from the xskb pool list, it doesn't reinitialize the node pointers. This means list_empty() will return false even after the node has been removed, causing xp_free() to incorrectly skip adding the buffer to the free list. Fix this by using list_del_init() instead of list_del() in all fragment handling paths, this ensures the list node is reinitialized after removal, allowing the list_empty() to work correctly.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: Fix possible oob access in mt7996_mac_write_txwi_80211() Check frame length before accessing the mgmt fields in mt7996_mac_write_txwi_80211 in order to avoid a possible oob access.

In the Linux kernel, the following vulnerability has been resolved: can: usb: etas_es58x: correctly anchor the urb in the read bulk callback When submitting an urb, that is using the anchor pattern, it needs to be anchored before submitting it otherwise it could be leaked if usb_kill_anchored_urbs() is called. This logic is correctly done elsewhere in the driver, except in the read bulk callback so do that here also.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (macsmc) Fix regressions in Apple Silicon SMC hwmon driver The recently added macsmc-hwmon driver contained several critical bugs in its sensor population logic and float conversion routines. Specifically: - The voltage sensor population loop used the wrong prefix ("volt-" instead of "voltage-") and incorrectly assigned sensors to the temperature sensor array (hwmon->temp.sensors) instead of the voltage sensor array (hwmon->volt.sensors). This would lead to out-of-bounds memory access or data corruption when both temperature and voltage sensors were present. - The float conversion in macsmc_hwmon_write_f32() had flawed exponent logic for values >= 2^24 and lacked masking for the mantissa, which could lead to incorrect values being written to the SMC. Fix these issues to ensure correct sensor registration and reliable manual fan control. Confirm that the reported overflow in FIELD_PREP is fixed by declaring macsmc_hwmon_write_f32() as __always_inline for a compile test.

In the Linux kernel, the following vulnerability has been resolved: ipmi: Fix use-after-free and list corruption on sender error The analysis from Breno: When the SMI sender returns an error, smi_work() delivers an error response but then jumps back to restart without cleaning up properly: 1. intf->curr_msg is not cleared, so no new message is pulled 2. newmsg still points to the message, causing sender() to be called again with the same message 3. If sender() fails again, deliver_err_response() is called with the same recv_msg that was already queued for delivery This causes list_add corruption ("list_add double add") because the recv_msg is added to the user_msgs list twice. Subsequently, the corrupted list leads to use-after-free when the memory is freed and reused, and eventually a NULL pointer dereference when accessing recv_msg->done. The buggy sequence: sender() fails -> deliver_err_response(recv_msg) // recv_msg queued for delivery -> goto restart // curr_msg not cleared! sender() fails again (same message!) -> deliver_err_response(recv_msg) // tries to queue same recv_msg -> LIST CORRUPTION Fix this by freeing the message and setting it to NULL on a send error. Also, always free the newmsg on a send error, otherwise it will leak.

In the Linux kernel, the following vulnerability has been resolved: mptcp: pm: in-kernel: always mark signal+subflow endp as used Syzkaller managed to find a combination of actions that was generating this warning: msk->pm.local_addr_used == 0 WARNING: net/mptcp/pm_kernel.c:1071 at __mark_subflow_endp_available net/mptcp/pm_kernel.c:1071 [inline], CPU#1: syz.2.17/961 WARNING: net/mptcp/pm_kernel.c:1071 at mptcp_nl_remove_subflow_and_signal_addr net/mptcp/pm_kernel.c:1103 [inline], CPU#1: syz.2.17/961 WARNING: net/mptcp/pm_kernel.c:1071 at mptcp_pm_nl_del_addr_doit+0x81d/0x8f0 net/mptcp/pm_kernel.c:1210, CPU#1: syz.2.17/961 Modules linked in: CPU: 1 UID: 0 PID: 961 Comm: syz.2.17 Not tainted 6.19.0-08368-gfafda3b4b06b #22 PREEMPT(full) Hardware name: QEMU Ubuntu 25.10 PC v2 (i440FX + PIIX, + 10.1 machine, 1996), BIOS 1.17.0-debian-1.17.0-1build1 04/01/2014 RIP: 0010:__mark_subflow_endp_available net/mptcp/pm_kernel.c:1071 [inline] RIP: 0010:mptcp_nl_remove_subflow_and_signal_addr net/mptcp/pm_kernel.c:1103 [inline] RIP: 0010:mptcp_pm_nl_del_addr_doit+0x81d/0x8f0 net/mptcp/pm_kernel.c:1210 Code: 89 c5 e8 46 30 6f fe e9 21 fd ff ff 49 83 ed 80 e8 38 30 6f fe 4c 89 ef be 03 00 00 00 e8 db 49 df fe eb ac e8 24 30 6f fe 90 <0f> 0b 90 e9 1d ff ff ff e8 16 30 6f fe eb 05 e8 0f 30 6f fe e8 9a RSP: 0018:ffffc90001663880 EFLAGS: 00010293 RAX: ffffffff82de1a6c RBX: 0000000000000000 RCX: ffff88800722b500 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffff8880158b22d0 R08: 0000000000010425 R09: ffffffffffffffff R10: ffffffff82de18ba R11: 0000000000000000 R12: ffff88800641a640 R13: ffff8880158b1880 R14: ffff88801ec3c900 R15: ffff88800641a650 FS: 00005555722c3500(0000) GS:ffff8880f909d000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f66346e0f60 CR3: 000000001607c000 CR4: 0000000000350ef0 Call Trace: <TASK> genl_family_rcv_msg_doit+0x117/0x180 net/netlink/genetlink.c:1115 genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0x3a8/0x3f0 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x16d/0x240 net/netlink/af_netlink.c:2550 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline] netlink_unicast+0x3e9/0x4c0 net/netlink/af_netlink.c:1344 netlink_sendmsg+0x4aa/0x5b0 net/netlink/af_netlink.c:1894 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg+0xc9/0xf0 net/socket.c:742 ____sys_sendmsg+0x272/0x3b0 net/socket.c:2592 ___sys_sendmsg+0x2de/0x320 net/socket.c:2646 __sys_sendmsg net/socket.c:2678 [inline] __do_sys_sendmsg net/socket.c:2683 [inline] __se_sys_sendmsg net/socket.c:2681 [inline] __x64_sys_sendmsg+0x110/0x1a0 net/socket.c:2681 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x143/0x440 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f66346f826d Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffc83d8bdc8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f6634985fa0 RCX: 00007f66346f826d RDX: 00000000040000b0 RSI: 0000200000000740 RDI: 0000000000000007 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6634985fa8 R13: 00007f6634985fac R14: 0000000000000000 R15: 0000000000001770 </TASK> The actions that caused that seem to be: - Set the MPTCP subflows limit to 0 - Create an MPTCP endpoint with both the 'signal' and 'subflow' flags - Create a new MPTCP connection from a different address: an ADD_ADDR linked to the MPTCP endpoint will be sent ('signal' flag), but no subflows is initiated ('subflow' flag) - Remove the MPTCP endpoint ---truncated---

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix a UAF issue in bpf_trampoline_link_cgroup_shim The root cause of this bug is that when 'bpf_link_put' reduces the refcount of 'shim_link->link.link' to zero, the resource is considered released but may still be referenced via 'tr->progs_hlist' in 'cgroup_shim_find'. The actual cleanup of 'tr->progs_hlist' in 'bpf_shim_tramp_link_release' is deferred. During this window, another process can cause a use-after-free via 'bpf_trampoline_link_cgroup_shim'. Based on Martin KaFai Lau's suggestions, I have created a simple patch. To fix this: Add an atomic non-zero check in 'bpf_trampoline_link_cgroup_shim'. Only increment the refcount if it is not already zero. Testing: I verified the fix by adding a delay in 'bpf_shim_tramp_link_release' to make the bug easier to trigger: static void bpf_shim_tramp_link_release(struct bpf_link *link) { /* ... */ if (!shim_link->trampoline) return; + msleep(100); WARN_ON_ONCE(bpf_trampoline_unlink_prog(&shim_link->link, shim_link->trampoline, NULL)); bpf_trampoline_put(shim_link->trampoline); } Before the patch, running a PoC easily reproduced the crash(almost 100%) with a call trace similar to KaiyanM's report. After the patch, the bug no longer occurs even after millions of iterations.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Use correct version for UAC3 header validation The entry of the validators table for UAC3 AC header descriptor is defined with the wrong protocol version UAC_VERSION_2, while it should have been UAC_VERSION_3. This results in the validator never matching for actual UAC3 devices (protocol == UAC_VERSION_3), causing their header descriptors to bypass validation entirely. A malicious USB device presenting a truncated UAC3 header could exploit this to cause out-of-bounds reads when the driver later accesses unvalidated descriptor fields. The bug was introduced in the same commit as the recently fixed UAC3 feature unit sub-type typo, and appears to be from the same copy-paste error when the UAC3 section was created from the UAC2 section.

In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Return the correct value in vmw_translate_ptr functions Before the referenced fixes these functions used a lookup function that returned a pointer. This was changed to another lookup function that returned an error code with the pointer becoming an out parameter. The error path when the lookup failed was not changed to reflect this change and the code continued to return the PTR_ERR of the now uninitialized pointer. This could cause the vmw_translate_ptr functions to return success when they actually failed causing further uninitialized and OOB accesses.