CVEs

In the Linux kernel, the following vulnerability has been resolved: netfilter: ebt_nflog: pin the NFLOG backend nf_log_unregister() runs after the per-net teardown so its final RCU grace period also drains readers that obtained the logger from a per-net binding. However, ebt_nflog passes an explicit ULOG log type to nf_log_packet() without holding a reference on the selected logger module, unlike the xt_NFLOG and nft_log frontends. An ebtables nflog rule can therefore remain callable while nfnetlink_log is unloaded. The resulting interleaving is: CPU 0 CPU 1 nfnetlink_log_fini() unregister_pernet_subsys() kfree(nfnl_log_pernet(net)) ebt_nflog_tg() nf_log_packet() nfulnl_log_packet() instance_lookup_get_rcu() The global ULOG logger is still registered at this point, so CPU 1 dereferences the per-net state after CPU 0 has freed it. KASAN reported: BUG: KASAN: slab-use-after-free in instance_lookup_get_rcu Read of size 8 at addr ff110001052e6210 by task poc/92 Call Trace: instance_lookup_get_rcu+0x1ce/0x1f0 [nfnetlink_log] nfulnl_log_packet+0x248/0x2fb0 [nfnetlink_log] nf_log_packet+0x204/0x300 ebt_nflog_tg+0x351/0x550 ebt_do_table+0xedf/0x22b0 Allocated by task 90: __kmalloc_noprof+0x186/0x470 ops_init+0x6d/0x420 register_pernet_operations+0x2f6/0x670 register_pernet_subsys+0x23/0x40 Freed by task 93: kfree+0x131/0x3c0 ops_undo_list+0x3e3/0x700 unregister_pernet_operations+0x232/0x490 unregister_pernet_subsys+0x1c/0x30 nfnetlink_log_fini+0x34/0x450 [nfnetlink_log] Acquire the ULOG logger module reference when an ebt_nflog rule is validated and release it when the rule is destroyed. Request the NFLOG backend for legacy callers when needed, matching xt_NFLOG. This prevents module teardown until all ebt_nflog rules have stopped using the logger.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: mrp: fix uninitialised bytes on the wire br_mrp_alloc_test_skb() builds MRP test frames on an skb from dev_alloc_skb(), which does not clear the linear data area. On the MRA ring-role branch the sub-option TLV header is appended with sub_tlv = skb_put(skb, sizeof(*sub_tlv)); sub_tlv->type = BR_MRP_SUB_TLV_HEADER_TEST_AUTO_MGR; so sub_tlv->length is never written, and the two trailing alignment bytes are appended with a bare skb_put() that does not clear them either. The neighbouring oui and sub_opt regions are explicitly zeroed, so three uninitialised bytes are left in every MRA MRP_Test frame that goes out. Put the sub-option TLV header and the alignment padding in a single skb_put_zero(), which clears both. The AUTO_MGR sub-TLV carries no payload, so the zeroed length field is already the value it should have.

In the Linux kernel, the following vulnerability has been resolved: futex: Prevent robust futex exit race some more A robust futex unlock stores 0 over the whole futex value - wiping FUTEX_WAITERS - and wakes a single waiter. That wakeup is a one-shot notification: the protocol relies on its recipient to either acquire the futex (and eventually unlock while aware of the remaining contention) or re-arm FUTEX_WAITERS before sleeping again. If the woken waiter is killed before it can do either, the kernel must jump in and wake the next task down the line. This is a known complication of the futex protocol with a previous partial fix in commit ca16d5bee598 ("futex: Prevent robust futex exit race"). Unfortunately, that fix is insufficient. If a third task re-acquired the futex through the uncontended fast path in the meantime, the notification is lost: robust exit processing sees that it is owned by another task and does nothing, while the new owner sees no FUTEX_WAITERS when it unlocks and wakes nobody. The remaining waiters sleep forever behind a free futex: A owns the futex, B and C sleep in FUTEX_WAIT uval == A | FUTEX_WAITERS A robust unlock: store 0, FUTEX_WAKE(1) wakes B uval == 0 D fast path acquire: cmpxchg(0 -> D) uval == D, no FUTEX_WAITERS B killed before acting on the wakeup B exit walk, pending op: owner D != B -> no action D unlock: no FUTEX_WAITERS -> no wake C sleeps forever This is clearly a shortcoming in the implementation, which fails to keep the FUTEX_WAITERS bit consistent. Work around this by augmenting the robust list exit processing to also perform the extra wakeup if the futex word is owned by another thread but FUTEX_WAITERS is not set. This does not fix the problem of a non-contended take over/release and free sequence, which has been discussed for years and has been addressed by commit 3ca9595d9fb6 ("futex: Add support for unlocking robust futexes") and subsequent changes, but failed to take the problem described above into account. A more complete solution which is based on the in kernel unlock of contended robust futexes has been discussed in the context of this change and should show up in mainline sooner than later. [ tglx: Amend change log slightly and fixup coding style ]

In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix fib_nlmsg_size() for RTA_VIA nexthops fib_nlmsg_size() still estimates nexthop space as if every gateway is encoded as an IPv4 RTA_GATEWAY attribute. IPv4 routes can also carry an IPv6 gateway, which fib_nexthop_info() dumps as RTA_VIA. As a result, route notifications can allocate an skb that is too small. fib_dump_info() then fails with -EMSGSIZE and rtmsg_fib() hits the WARN_ON() that marks such failures as a fib_nlmsg_size() bug. With panic_on_warn set, this becomes a kernel panic. Mirror the actual nexthop dump layout in fib_nlmsg_size(): account for IPv6 nexthop gateways dumped as RTA_VIA, for the no-header rtnexthop layout used inside RTA_MULTIPATH, and for RTA_FLOW only when it is actually present.

In the Linux kernel, the following vulnerability has been resolved: ipv4: fix use-after-free in fib_nhc_update_mtu() fib_nhc_update_mtu() walks the nexthop exception table under RTNL, but RTNL does not serialize this walk with PMTU exception updates. The walk uses rcu_dereference_protected() with a constant true condition without holding fnhe_lock. The following interleaving can therefore occur: CPU 0 CPU 1 fib_nhc_update_mtu() update_or_create_fnhe() load fnhe spin_lock_bh(&fnhe_lock) fnhe_remove_oldest() unlink fnhe kfree_rcu(fnhe, rcu) <quiescent state> access fnhe after grace period KASAN reported: BUG: KASAN: slab-use-after-free in fib_nhc_update_mtu+0x3df/0x410 Read of size 8 at addr ffff888107d49000 by task poc/90 Call Trace: fib_nhc_update_mtu+0x3df/0x410 fib_sync_mtu+0x7a/0xd0 fib_netdev_event+0x229/0x3f0 netif_set_mtu_ext+0x33a/0x570 dev_set_mtu+0x88/0x120 The same walk updates fnhe_pmtu and fnhe_mtu_locked. These fields form a pair and other writers serialize them with fnhe_lock. RCU alone prevents reclamation, but would still allow concurrent writers to leave a mixed pair. Walk the table under RCU and acquire fnhe_lock only while updating each exception. RCU keeps the current entry alive while the short critical section serializes its paired PMTU fields. This avoids holding the global lock while scanning all 2048 buckets for every nexthop.

In the Linux kernel, the following vulnerability has been resolved: serial: qcom-geni: fix TX DMA buffer flush When transmit flushing a qcom-geni UART during an ongoing TX DMA, the UART gets stuck infinitely repeating corrupted TX DMA frames. The DMA-mode uart_ops does not provide a flush_buffer callback, so an in-flight transfer can complete after serial core has reset the transmit kfifo, underflowing its length and resubmitting page-sized transfers indefinitely. Add one that stops the transfer and clears tx_remaining and tx_queued. The stop path was also broken: it unmapped the buffer while the serial engine could still read it, and never reset the TX DMA state machine. Cancel the main sequencer command first, then reset the state machine and wait for it before unmapping. Drop the early return so a pending mapping is also cleaned up when the main command is inactive. The bug can be triggered from userspace with a large write immediately followed by TCOFLUSH. A following tcdrain will hang forever. The bug was reproduced and this fix was validated on Arduino Uno Q (QRB2210) using /dev/ttyHS1.

In the Linux kernel, the following vulnerability has been resolved: serial: 8250_dma: Clear stale RX state on shutdown serial8250_release_dma() terminates RX DMA and releases the channel, but leaves rx_running set. If the port is closed while an RX transfer is active, the stale state remains while rxchan is NULL until the channel is requested again on the next open. The DesignWare BUSY workaround added by commit a7b9ce39fbe4 ("serial: 8250_dw: Ensure BUSY is deasserted") calls serial8250_rx_dma_flush() from the LCR write path during startup. This happens before serial8250_request_dma() obtains a new RX channel. On reopen, the stale rx_running state therefore makes the flush path pass a NULL channel to dmaengine_pause(), causing a kernel Oops. Clear rx_running after terminating RX DMA, matching the TX cleanup. Also make the flush helper return if the DMA object or RX channel is not available so startup and teardown paths cannot pass a NULL channel to the DMAengine API.

In the Linux kernel, the following vulnerability has been resolved: serial: 8250_of: clear stuck empty-FIFO RX-timeout on LPC32xx The NXP LPC32xx UART (PORT_LPC3220) can latch an RX character-timeout interrupt while the RX FIFO is empty: IIR reports UART_IIR_RX_TIMEOUT (0x0c) but LSR.DR is clear. A character timeout is only cleared by reading RHR, but serial8250_rx_chars() reads RHR only when LSR.DR is set, so nothing ever clears the condition. The interrupt is level-triggered and re-fires immediately, so on a single-core ARM926 the resulting interrupt storm livelocks the CPU. It is reproducible when userspace repeatedly opens the front-panel port (ttyS1): serial8250_do_set_termios() re-enables interrupts on unlock and the handler then spins forever with iir=0xcc lsr=0x60 ier=0x05, tripping the soft-lockup detector in serial8250_handle_irq_locked(). LPC32xx has no dedicated 8250 glue driver, it's driven by the generic 8250_of. Add a hardware specific handle_irq for PORT_LPC3220, wired up in of_platform_serial_setup() the same way fsl8250_handle_irq is installed. The handler follows dw8250_handle_irq(): on an RX timeout with an empty FIFO (LSR.DR and LSR.BI clear) it does one throwaway RHR read to clear the condition, then calls serial8250_handle_irq_locked(). No real received data is ever discarded, and it is a no-op on healthy UARTs which never report a timeout with DR clear. This is the same class of bug already worked around in other 8250 drivers; see commit 424d79183af0 ("serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt") which reports the identical iir=0xcc/lsr=0x60. See also UART_RX_TIMEOUT_QUIRK in 8250_omap, and the note in 8250_bcm7271.

In the Linux kernel, the following vulnerability has been resolved: serial: amba-pl011: cancel RS485 hrtimers after freeing IRQ The RS485 trigger hrtimers are embedded in the devm-managed port and can fire after it is freed. The IRQ handler can arm a timer, so free the IRQ first and then cancel both timers. Complete the RS485 stop without arming a timer, and cancel the timers in remove() for the suspend-then-unbind path, where shutdown is not called. This issue was found by an in-house static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix OOB read in rtw_get_wpa_ie() rtw_get_wpa_ie() reads bytes at fixed offsets into a vendor-specific information element without checking that the element is long enough, causing an out-of-bounds read for a short trailing IE. The function locates a vendor-specific IE (EID 221) with rtw_get_ie() and then compares a 4-byte OUI+type at pbuf + 2 and reads a 2-byte version word at pbuf + 6. Those accesses require the IE body to be at least 6 bytes, but rtw_get_ie() only guarantees that the element fits within the buffer; it does not enforce a minimum body length. A vendor-specific IE whose length byte is 0 to 5, placed at the end of the buffer, therefore makes these reads run past the end of the IE and past the end of the buffer itself. The buffer holds information elements taken from received management frames and from the IE blob passed to rtw_cfg80211_set_wpa_ie(), which is kmemdup'd to its exact length, so the read can run off the end of the allocation. The sibling helpers rtw_get_sec_ie(), rtw_get_wapi_ie() and rtw_get_wps_ie() in this file already reject too-short vendor-specific IEs before their OUI memcmp(); rtw_get_wpa_ie() was never brought in line with them, and needs a minimum of 6 rather than 4 bytes because of the version word. Add the missing length check.